Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hello,
I have configured MQTT over TLS to connect to our broker. Everything works great except that the modem stops reconnecting to the broker after exactly 22 connect-disconnect...
Hi, I'm trying to run the nfc_pairing example from the master branch (1.3.99) of NCS. I've successfully built the example in SES and loaded it onto my nRF52840DK, but the...
I'm wondering how BLE signals are handled at the layer below the scanning module. Namely, suppose there are hundreds of BLE modules that are all advertising nearby. How does...
Hi
We are developing a 70 x 70mm PCB containing a nRF52840 for BLE/ESB and a second module for WiFi/BT.
We have no mechanism to avoid transmission of the WiFi module while...
Hi. Sorry, can't find the answer on the forum on my problem.
I am using:
nRF52840 DK
Segger
MacOS
Fanstel BC840 module
I have a project that flashes to Raytac...
Are there any examples of how to enable and use coded phy long range with the nRF Connect SDK? I have the nrf52840DK and would like to create an advertising example to test...
Hello,
In my current project designed around nRF52840 incorporating many peripherals (limited power budget) and many central devices. Each peripheral can connect to any...
Hi
I am using NRF52810 with Softdevice S112 7.0.1 and SDK 16
I want to ask about the behavior of the softdevice notification queue on disconnect. I have seen these two...
Hi .thank u for reading this .First sorry for my english. This is the story:
I try to make a flexible mesh using multi nrf24l01+ more than 10 nodes. I searched so many topic...
While running a Scan in nRFConnect 4.24.3 on Android 10, Nokia 6.2, I see the first Advertisement from my BLE Device. That device advertises different sets of ScanData over...
Hi ,
I am working on a project where i need to publish wifi scans over ble , issue is that when ever we try to send data over it either send or not sent to avoid data loss...
Does Nordic have some solution for this? Device would be a WiFi+BLE gateway, which runs Linux, and can support advertising scan for at least 300 beacons, and have Ethernet...
Hi, I am running into issues where the nRF9160 (in NB-IoT mode) does not seem to handle cell changes reliably. I am using modem firmware mfw_nrf9160_1.2.0 . I made a simplified...
Hi Nordic guys,
I'm trying to create a pin pairing between an NRF52 DK and iPhone.
I've created this function to do that:
I've added that function in the ble_peripherical...
