Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hello,
I work on nbiot evaluation and i try to send udp data from my basement.. I boot and attach network from ground-floor and when i'm on PSM mode im going on basement...
I want to run the board at 1.8V and run the uart and spi examples on my laptop. What should be my configurations and which micro-usb port shall I use to connect with laptop...
Hi,
I'm trying to send custom messages between server and client, based on the light switch example. I've modified button_event_handler and the client was able to receive...
Hi Nordic team,
I have an issue: I have to program/flash my mesh application together with softdevice140, mesh-bootloader and device settings page on the nrf52840 chip....
Hi everyone,
I am facing a kind of a strange problem. I want the system to enters system OFF mode when a certain pins goes to LOW. For that reason I have include code section...
I plan to use the nRF52833 or nRF52840 chip and as usual it needs a charger circuitry “PMIC” to charge the battery "Li-Ion"
Is there any special PMIC version recommended...
I'm using nRF52810 in a CR2032 battery powered device.
I use the DCDC mode to enhance power consuption. According to Product Specification in release 1.3 (and unlike nRF52840...
Hi,DevZone
I'm not Native English , sometimes can not express exactly, So, I'll provide a concise description about the question
1, platform: nRF52832_QFAA _E1, nRF5_SDK_13...
I used the NFR connect tool to install softdevice on the NRF52840 Dongle. I see noise about another tool to set up this kit in this forum; these are old. I forget what it...
Hello,
In our application, the central device will connect to one peripheral node at a time, collect the data, and disconnect it. There may be more than 30 to 40 peripheral...
Hi
I have two board nrf52833 along with the antenna array.
I want to implement Angle of Arrival.
I want to know from where can i start. any demo example
please me...
The global window in Nordic SES does not display the static global variables. I am probably missing something very simple, but I can't figure out how to view them when single...
At the very beginning of the program in the main function, my stack pointer is 0x20026390, although I expected it to be in the 0x20040000 area.
In this case, static memory...
Hi, I am using a thingy 52 board. I have Arm jlink programmer to load the program. And I have loaded the program successfully. But I want to debug the code. So, How can I...
Hi I looked at the lte_ble_gateway sample in the nrf connect sdk and noticed that we are able to simple call bt_ready() as if the nrf9160 is an nrf52 device. How is that possible...
