Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
I am currently using nRF8001 in my board (configured to connect - send data - disconnect - sleep every 30s cycle time). However, I am measuring about 140uA in average and...
Hello there.
I'm developing a custom board for the nrf52810 chip. I'm taking the reference files as a base for my own design, but I'm a little bit confused on which files...
Hi,
I am using nRF52840, SDK 15.0, softdevice 6.0.0 (toolchain IAR 7 on windows).
My application runs on FreeRTOS 9.0.0 tickless (NRF_SDH_DISPATCH_MODEL 2).
I have a...
Hi,
I want to get Battery ADC Value.
So. I simply used nrf_drv_saadc_sample_convert() function.
At first I thought it was the right value,
Later, I found that the...
Hi,
I want to get Battery ADC Value.
So, I simply used nrf_drv_saadc_convert()
At first I thought it was the right value,
Later, I found out the wrong value.
If...
Hello, Nordic.
I am working on an iOS App that uses a MPU9250 sensor to display a 3D simulation screen in my app. (It is same as motion control in Thingy52 App).
I...
Hi,
I am using PCA10028 development kit for sniffer with wireshark 3.0.1 using sniffer version V2.0 beta 3 . I am getting issue like "Encrypted packet decrypted incorrectly...
Greetings,
I was wondering why Amazon FreeRTOS demo wont work on nRF52840 DK. After following all the steps even building a bootloader on my board, my demo is running but...
SDK 14.0,
IC:NRF52832
I want to save some data in the flash via the FDS. firstly i write 3 records then the next I want to read them one by one according to the record...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image. I am using ‘ble_app_blinky’.
1) If I configure any GPIO as state change trigger...
I used Win 7.
I updated the nRF connect application to use with the nRF dongle.
The Microsoft wireless mouse and keyboard is shown like nRF Connect DFU Trigger. Also internal...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex?-M4F 32 bit processor...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image. I am using ‘ble_app_blinky’.
1) What is the difference between High-accuracy...
Hello
I am using Android and BLE communication with nRF52832 (BLENano2) now.
I am using SDK 15.0.0 with keil uversion.
Central is Android and peripheral is nRF52832...
