Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Recently got my Nordic Thingy:52 which is based of nRF52832. I wanted to test sending the data to cloud, so I just followed the IFTTT tutorial on the Android Nordic app. I...
For a design consulting client, they have a startup problem and need to know the approximate leakage current when a GPIO is in "DISCONNECTED" state.
I know the NFC pins...
I am using Uart Ble example of sdk , i want to write to Tx without UART can u please help me do it
i actualy want to send accelerometer data which is of size 40kb after...
Hi, I have added BLE custom characteristics in my application. I am writing and reading some values through ble scanner mobile app. Here i observed that when i enter string...
Hi,
I trying to use higher MTU size for my application and i have followed the att mtu throughput example. it is working fine upto 50 bytes packet size but when i try...
so, after getting it to compile, now i can no longer write to flash memory and i don't knwo why i am getting this error now. now sure if it is a result of nrf_dfu_flash and...
hi.....
i am interested in Mesh ,actually i want to understand the flow of mesh program (eg light switch example )how does it work,how it transferring from client to server...
Hi all,
In order to lower the power consumption of my device I have been experimenting with WFE. When using WFE I see that the interrupt latency is increased from ~4µs to...
Onl
I have 40 kb of data i need to send, and what i thought was using notification by creating a timer, which will be started as soon as device gets connected, in...
I am trying to interface with a I²C OLED display using Zephyr’s SSD1306 driver. The driver uses i2c_burst_write, which itself requires that i2c_transfer support gather writes;...
This is on SDK 15 : Not all services are reported when doing service discovery on more than one connection at a time.
Basically, ' ble_db_discovery .c' uses ' m_pending_usr_evt_index...
Hello, I am using the nRF51422 Development kit with SDK11. I am using the proximity application for the battery level service. I would like to strictly advertise to a single...
Hi,
I have an application where I have for example 5 BLE transmitting devices . Each device has one push button and each device is assigned to a number 1-5. I also have...
Dear nordic,
I am new in this open thread i tested your examples its working fine. i also tested CLI example i think its working but i didn't see a response in terminal...
I have a few Bluetooth transmitters based on nRF52832. My receiver devices are mainly iOS and Android mobile devices. I'm considering of replacing them with nRF52840 for Bluetooth...
