I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
SDK version 15.2.0 (latest at the moment of writing). I am having trouble reading from UART in > 1 byte chunks where exact length is not known upfront.
The problem is, UART...
Hi everyone !
I'm working with an example code for the nRF52840.
I added some c files and changed from UART to SPI.
Until this point everything was able to compile and...
Hello,
I have to send 15 bytes on uart of nRF52832 (nordic micro is the receiver), but I have APP_UART_COMMUNICATION_ERROR. If I send 5 bytes everything works fine, if I...
I have a beacon from Wellcore, w912, with NRF51822QFAAH0. I use NRF Connect and I see the temp and accel sensors but I dont know how to enable them. Is there a manual you...
In section 23.1 "EasyDMA" of the Product specification, it is written that "the S0INCL field in PCNF0 determines if S0 is present in RAM at all if its length is zero." But...
Hi I am building a project, where I need to initialize the ADC using a timer. Whenever there is a timer interrupt "nrfx_saadc_sample" gets called and ADC starts sampling....
I want to find the mac address of the nRF52 DK and assign the instance ID of the eddystone format.
I am using the eddystone sample app from the SDK 152 and softdevice 6...
Hi,
I would like to build an application on Ubuntu PC, using github.com/.../nrf52-ble-image-transfer-demo The purpose is to do some analysis of the images taken by Arducam...
Hey everyone, I'm having an issue communicating with a QSPI flash on a custom development board, using the nRF52840. The flash is a Winbond W25Q16JVSSIQ. Schematic and pins...
Hi,
I am using a custom NRF52832 board. I am using Nordic SDK + BLE code, and whenever I am trying to do an erase of flash memory with start address as 0x70000 and end address...
I try to get the info listed in the following paragraph (From the nRF91_DK user guide) but just get run the run around with the web site. Anyone got a link to this information...
The flash requirements for both the S132 v5.0.0 and v5.1.0 are the same, however the size of the v5.1.0 softdevice is quite a bit smaller.
S132 v5.0.0 uses flash addresses...
Hello I try to get the mac address of connected device
/**@brief Function for the application's SoftDevice event handler.
*
* @param[in] p_ble_evt SoftDevice event...
Issue with Zephyr software platform and sleep state for the Nordic chipset. We can see when using the power management sample code for Zephyr that it consume 300 uA in sleep...
