Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hi
Newbie in the nRF family of products so i might have missed the answers to my questions somewhere in the documentation and forum. if so i apologize.
I'm trying to get...
Hello ALL,
I have been using UART module and fstorage module in an application. I've been sending a bin file from PC to NRF52 using UART but when I tried to save it using...
Hi All,
I have some code that I'm porting from a Zilog platform over to the nRF52 platform. The code uses 1 timer and 1 uart. The goal of the code is to handle RS485 messages...
I am testing the IoT_lwip_MQTT_publisher_pca10056_s140 example project from SES on Windows.
I build and install the kernel with 6LoWPAN module on the Rpi3!
I can run from...
Hello，I'm from China。
At present, there is a need to broadcast beacon data in nrf51822 (SDK_12.3.0_d7731ad is used as the protocol stack version, and the...
Hi
I want to generate two PWM signals that are phase shifted with 90 degree, with similar duty cycle. I have the following pwm configuration, but I don't know how to proceed...
I am operating as a Central. How do I register and enable a discovered characteristic's indication?
I do the following and the subscribe passes but then the kernel crashes...
I'm planning to buy a nRF51822 based module for my BLE project & I wanted to know whether any of the nRF51822 based modules come with OTA ready bootloader out of the box....
Hi,
I'm trying to save sensor data to sd card on low power mode. When i connect to bluetooth mobile app can pull all data from sd card.
How can make this architecture...
Hi,
I'm using Nordic BLE Sniffer. When I look into the captured data I see a lot of malformed packet (CRC error). It try to decode any received data even if there is CRC...
I was digging around a bit in my code to get a better grip on logging. In sdk_config.h, I have the following relevant settings:
My modules all implement their own logging...
I am going to implement DFU over BLE in my nRF52832 project. Since the size of my application + softdevice larger than half my memory size I wonder how the update is performed...
We're looking to use the nRF91 to measure the LiPo battery voltage to determine battery health. We would want to know what the accuracy and range of %XVBAT is. Looking at...
I am trying to create CTS server using nRF 52840 dongle and nRF Connect PC app (v2.6.1). Currently I can manually provide current time and local time information to the app...
