I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
Hi, the peripheral/spi example calls for nrf_drv_spi.h, which is located in the legacy directory in SDK 15. I found this post in the devzone:
[quote userid="2116" url="...
We're trying to implement OOB pairing where the 128-bit value is received externally (not NFC). All examples I could find are NFC related and seem to require the external...
Hi, everyone. We are developing BLE project on the chip nrf52832 with SDK 15.0.0 software. In this project we are using ppi feature. During the work the program must enable...
I am trying add the fatfs example in my custom solution and I have the follow error after add the paths and files.
nrf_log_frontend.c:92:35: error: unknown type name 'nrf_log_module_dynamic_data_t...
Hi,
I am working for Adafruit on the bootloader for the upcoming feather nRF52840. Currently testing using the nrf52840DK pc10056. Everything is OK with S140 6.0.0 . Today...
I need to implement a 4kHz signal to drive a buzzer on a custom board of nRF51822 with external 16MHz and 32kHz crystal.
I am using Timer1+PPI+GPIOTE to generate this 4kHz...
I'm currently using:
- Board: NRF52840
- SDK for Mesh 2.1.1
- SDK for Thread and Zigbee v1.0.0
My problem is that I want to merge and run both Bluetooth Low Energy...
Hi, I am using nRF SDK 12.0.0_12f24da, with nRF52832 on pca10040 hardware, and working with the example in examples/peripheral/spi/main.c
Initially I was working on integrating...
Hi, I am using nRF52840-DK; Window 10; Embedded Studio and try to run sample project:C:\Nordic_Semi\nRF5_SDK_15.0.0_a53641a\examples\peripheral\ uart \pca10056\blank\ses ...
Hi all, I'm using nrf52832 with SDK15 in my project. For debugging purposes I need both CLI and LOG modules enabled with RTT as a transport. I followed this manual to setup...
How can I disable NRFX_LOG_INFO calls in the PPI driver? I've set NRFX_PPI_CONFIG_LOG_ENABLED 0 and even NRFX_PPI_CONFIG_LOG_LEVEL 0 but that doesn't stop messages like the...
Hi,
This is Srivisakh. I am using a custom made board integrated with nrf52832 board in which UART is configured. I am using Segger IDE for code development and building...
Hello I have what I hope is a simple question regarding the Internal DC/DC on the nRF52832 and thus nRF52810. I am assuming it is the same internal design, correct between...
We are just in the very beginning of developing a mesh network with 150 devices and a gateway (with a nRF52840 in it). We want to find the best strategy for provisioning....
