I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hi,
I develop on nRF52 with linux/eclipse but to debug, I would like to use the sniffer. This one is only available on windows then I try to install it on a Windows 7 64bits...
I have successfully implemented Scanning and Advertising at the time using s132 on nrf52832 with SDK14, it works very stable and fast which satisfied me.
Recently, I was...
Hello,
I've been using the SDK 15's "ble_app_uart" example and I've been curious on how the function nus_data_handler() gets called after data is sent over BLE. More specifically...
hello,
I am newer to nrf. I am using nrf52832 development kit and using soft device 5.0.
I have confusion with two function with nrf_log_info and printf?
which should...
Hi,
I want to know if we can send Mobile Notifications or send sms to nRF52832. i want to do some operation based on notification or sms received from sms on mobile..
Hi,
I am currently trying to setup my sdk 15 on my pca10040. I already have a working I2C source for a BME280 and it works fine using the SDK 12 (pca10040), I get the current...
Development Kit PCA 10056, Ver 1.0.0, SDK 15.0.0, Softdevice 140 6.0.0
If I try advertisement with the template-example combined with NFC text record at the same time, the...
I know that the SoftDevice has support for controlling a frontend with TX and RX signals.
However, our radio module uses a Skyworks SE2431L frontend with the control signals...
When using the script interactive_pyaci.py together with ipython and the serial example, I observe a strange formatting in the command window, because the "In [..]" is often...
SDK is nRF5_SDK_13.1.0_7ca7556.
Example is ble_ant_app_hrm.
Softdevice is S332.
The example can connect android but can not connect iphone.
Iphone 7 and ios is 10...
Disconnection of the peripheral is done without enabling another connection, the only way is to reset the module.
It happens sometimes after 5 min up to 1-2 hours.
If...
Hi all,
I'm working on an application that requires BLE. I've recently upgraded my project from sdk 14.0 to 15.2 in order to deal with some problems that I ran into with...
Hi,
I am trying to configure the nRF52810 clock setup to accept the LF CLK source from a pin on stm32l4xx on a custom board without much luck. My setup works correctly if...
