Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hi All,
Im very new to this how firmware space and would love some help.
Currently i have a NRF52840 DK Board with a Seeed Canbus shield. ( CAN-BUS Shield V2.0 | Seeed...
1. Hi i am using nrf52840 sdk ver 17.1.0 in secure bootloader /pca10056_uart_debug
2. I have flashed the dfu uart code without any change
3. while performing dfu via uart...
We are developing a ZigBee-based end device using the nRF52840. We have implemented most of the functionalities and also reporting and are able to receive reporting information...
I am working on a wearable which has Fanstel BT40F MCU (SOC nrf 5340). when i initially turn on my pmic, it can only generate 1.8 volt from buck 1 regulator and I am thinking...
Hello!
I have a custom board with an nRF52805 on it and I am simply trying to run the Zephyr blinky example and verify I can see a GPIO toggling as my first step. I installed...
Hello, I'm currently looking for a comprehensive example of DFU-OTA (Device Firmware Update Over-the-Air) using the latest SDK version with the nRF5340 platform. If anyone...
Hello im using Dwm1001C with NRF SDK 14.2 for uwb localization measurements. I have a example project that measures the position of the tag. Inside this project at some places...
I am developing application using nRF Connect SDK (v2.5.2) on custom design based on nRF52840. The design is a prototype device and currently have dozens of them assembled...
Hello!
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am integrating NUS central...
Dear Nordic Team,
I have a question regarding the integration of Google Find My Device into the Nordic SDK.
Our company is already registered with Google for a Find...
Hello everyone,
I’m currently exploring the Nordic Asset Tracker V2 as a foundation for my project. During my investigation, I noticed that the solution exclusively uses...
Hello all, I'm using the adafruit itsy bitsy for this modbus project and having issue to communicate with my usb-rs485 using modbus poll software. The protocol is Modbus RTU...
Hi, we're having some problems and need help. We have a usage scenario: in HOST mode, the switching rate is 250k/2M every 10ms, the time slots of the two rates are different...
Dear Team, I'm facing the issue of insufficient stack or stack overflow when I enabled configCHECK_FOR_STACK_OVERFLOW and configUSE_MALLOC_FAILED_HOOK. If i am not enable...
