Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
I have read the related issues, none of them provided a solution for me. There was one answer which suggested to downgraded libstdc++6 as a solution without giving any specific...
Recently, I have been working on integrating mcuboot with the partition manager from the NCS sdk. In addition, for another project, I am using Zephyr upstream and using Sysbuild...
I need to get the number of items stored in a fcb and there doesn't seem to be an easy way to get the count from the current read position (fcb_entry struct).
Can anyone...
Hi!
I use SDK15.0 and s132_nrf52_6.0.0_softdevice
I use nRF52 in two modes- peripherial and central in one time.
When I use it like peripherial and have connect with...
I am using RTT to debug my application and it's fine when it's working. The problem is that it seems to be flaky as hell. Sometimes it just stops working without any apparent...
I'm using the NCS 2.5.2 sdk and nrf 5340 with 7002, and I want to do BLE OTA DFU using external flash.
I've found this guide Add DFU support to your application - Software...
Hi,
I am learning my way with Zephyr on nrf5340 SoC, an loving it so far. Unfortunately I got stuck on something that should work out of the box, the setup of the BLS subsystem...
Hi
I want to use button interrupt in NCS.
There is no button interrupt enabled in initialization.
My test environment:ncs2.6.0,nRF52840DK.
In nRF5SDK, I only need...
Hello,
I am experienced working with Arduino and have developed projects with the XIAO BLE that has an nRF52 in built.
Right now I am developing a software using the nRF52...
Hi,
I try to install nrf connect SDK using the nrf extension in visual studio code.
I get error messages like :
[west]: fatal: unable to access ' github.com/....
I have developed the low-level drivers for the MT29F4G01ABAFDWB (using spi) NAND flash and am currently using the Zephyr RTOS. I would like to integrate FATFS into my NAND...
I'm still a beginner，I don't understand why the board I designed can't run the nRF connect SDK application, but the nRF5 SDK 17 application can run normally. I want to know...
Hi,
I have been using the nRF52840 Dongle for at least three months without any issues. First, I implemented my project on the nRF52840-DK, then easily configured it for...
Hello,
In my code, I would like to use the power_down_unused_ram () function. I included the ram_pwrdn.h file but the build returns with undefined reference to `power_down_unused_ram...
Hello. I want to the use pwm_library example for setting a PWM on a GPIO. It works well except that the initial state of the GPIO is high for about 230us before the PWM starts...
