Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
I'm trying to setup a I2S module by referring the I2S module given in the nrf5340-audio application. This is my audio_i2s.c file.
Now when I'm building this...
What should I change to run the hci_lpuart sample with UART asynchronous API instead of the using the interrupt driven one? I have already changed the source file on the sample...
I was able to run blinky successfully on my customized nrf5340 board, but it doesn't respond to writing matter related code, there is no output from the RTT, I refer to the...
Hello,
I am reaching out regarding some challenges I've encountered with SPI communication on the nRF7002DK when interfacing with the ETH Wiz Click | Mikroe module and a...
Hello,
I am a student and new programmer and got the Thingy:91 for a project at Uni. I went through the getting Started guides and now I am at the point, where I downloaded...
I tried adapting the blinky sample project to work with a custom board. After an hour or two I was able to define the GPIOs of my schematic including I2C with the device tree...
Hello,
we are trying to implement a custom Friend node research policy, before the friendship is established.
Since bt_mesh_lpn_poll() works only when the frienship is...
Hello,
is there any example using the IEEE 802.15.4 driver?
I was able to send and receive a some packets by using nrf_802154_receive and nrf_802154_transmit_raw, and...
Hi,
i am playing around with configuration of Softdevice (S112 ) + bootloader + application.
Bootloader is custom, really simple. Flashing block of data received via uart...
Hello, I wanted to understand what is the default storage place in the internal flash memory region of persistent info for OpenThread. In the previous SDK (Thread and Zigbee...
Hello DevZone,
I have 2 Thingy91X (not Thingy91), with nRF9161 and nPM1300 inside. These two devices run out of battery for several hours.
The problem is that I can't...
Hi，I have some problems using the NFC routines in the SDK.
The hardware used is nRF5340 DK.
Software is nRF Connect SDK v2.6.99-cs1.
The downloaded and run routines...
Hi,
We have designed a custom board for npm1300 and nrf52832(MS50SFA2 module). We would like to drive the VCC of the BLE module using buck2 but we are only getting 1.8V...
Hi,
I have to use Nordic SDK and VS Code Dev Kit on my company enterprise PC but I cannot fetch the toolchain or install SDKs via VSCode or nRF Connect for Desktop
...
