Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi, For the Adafruit Feather nRF52840 board I cannot find any information about the RTC. On the Feather board the 32kHz crystal is connected to the RTC clock input (P0.00...
Hi
I want to migrate my application to Zephyr RTOS platform from old setup given below.
Old Setup: Hardware: nRF52832 board. Soft device: S132 Software: SEGGER Embedded...
Hi, I'm new to Nordic Semiconductor chips.
I have experience programming STM32 and Atmel microprocessors. I would need to program/debug the NORDIC nRF52832 chip, without...
Hello there, I am working on enabling/ disabling DFU in nrf52840dk using ncs 2.4.2. previously i was doing it using ncs 1.8.0 as follows: libraries used:
#include <mgmt...
Hi,
I use the above function to create a new dataset. When I use SDK 2.3.0, this works perfectly. But when I use SDK 2.6.0 I get the following.
When I tried
arm-zephyr...
Hi all!
So I'm just starting out with the Thingy 91 and I was following the Nordic Thingy 91: Getting Starting Guide and I was in the process of using MCUBoot to update...
I am using nrf7002-dk as client and running the server python code in my PC and I am using ngrok command line tool get alternate http link.
I am using wifi-fund lesson4...
Since https://github.com/nrfconnect/sdk-nrf has disabled issues, this is an assorted list of problems/limitations with the lte_net_if library ( https://github.com/nrfconnect...
Hi All,
I want to do dfu over uart with secure bootloader, am using nrf52840-DK, nRF5_SDK_17.1.0_ddde560 SDK and segger embedded studio V8.10.
compiled and flashed secure_bootloader_uart_mbr_pca10056_debug...
I use DWM3001C chip,it has a nrf52833 mcu inside.when i call ble_init() in main.c.it report error:
peer_manager_pds: Could not initialize flash storage. fds_init() returned...
Hi Team, I'm trying to port the acconeer project that worked on the old one NCS v2.2.0 to new NCS v2.5.2 and ran into a problem with the difference
c:/ncs/toolchains/c57af46cb7...
I am trying to use libmodem in a bare-metal app on a 9151dk, but nrf_modem_init() is hanging (not returning). What conditions can cause this? The issue looks a little like...
Hi there.
Right now, I'm facing the issue that I want to use the camera OV7670 with the nRF52833.
I don't know how to start or what example I can take as a base to start...
