Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Hi,
I am using NCS 2.1.2 with the [email protected] (but I have tested with 2.2.0-rc1 and it doesn't change anything). I have attached a simple example which should just...
Hi team,
I want know how many UART modules on nRF52840 microcontroller? I am confused with one UART and two UARTEs.
Which one is connected to "USB for interface MCU" connector...
Hi,
I have successfully followed the guide for setting up the AWS asset tracker application ( https://nordicsemiconductor.github.io/asset-tracker-cloud-docs/v2.1.x/docs...
Hi all,
I did add a reset switch on my custom board. I read some topics how to active it, but I´m not sure if I did it right.
I did add it in the preprocessor define:...
Hi Nordic,
Soft device is s140
SDK version is: nRF5_SDK_17.1.0_ddde560
Bootloader - Secure bootloader.
We are trying buttonless DFU process using secure bootloader...
Hello,
We are trying to use the nrf91 GNSS with the `nrf_modem_gnss` library. I'm looking for clarification on these fields that are listed in `struct nrf_modem_gnss_agps_data_location...
test setup
the custom board schematic
we tried to flash the custom board with the beacon sample here https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr...
I just upacked my new nRF52 DK and installed what I think are all the goodies to do development (on my Windows 11 laptop). I can see the board with the Programmer and I loaded...
Hi
I am using 4 x AD7410 in each TWI channel, using both TWI ports. So, altogether 8 AD7410s. ( I used the Adafruit breakout boards).
Initially I get the temperature readings...
The BOOT_SERIAL_WAIT_FOR_DFU feature is meant to wait a number of milliseconds (500 by default) for a message via serial comms. If it doesn't receive a message it continues...
Hello,
I have following problem:
I am using a multilink NUS Central. With one peripheral connection everything works fine. But when make a second connection I sometimes...
Dear support
Try to perform DFU OTA on my final target board and have an error state says - "payload(250 bytes) too long for MTU: 249 "during uploading stage, could anyone...
Hi,
I am developing application on NRF52840 with Zepyr 2.1.2 SDK, and I found two problems when using the example scan_adv, as follows:
Executing bt_le_scan_start in...
My team is developing for an nrf52840 on a custom design pre-production PCBA. Up till now we have been using nrf52840dk_nrf52840 in the"Board" field of the "Add Build Configuration...
Hi Team We’re using Nordic connect sdk 1.9.1 We’ve created a vendor service and defined multiple characteristics in same, We are using Nrf connect mobile app to fetch the...
