I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
We have come to understand that the nRF5340 will not support BT classic (multiple tickets confirming this). But we still have a use-case that requires both BLE Audio and BT...
Hi guys,
I'm writing firmware for the nRF52840 using Zephyr, based on the cdc_acm example, using zephyr,cdc-acm-uart. I'm trying to blast out a ton of data, and need to...
hi devzone.
I have commercial product(led light receiver) which has nRF52832 chip and is running as central mode.
I install 'nRF connect for mobile' in my android phone...
I could not find a way, where I can get the nrfx_rtc_t const *p_instance for the nrfx_rtc_init function. There is no example where it is shown where to get this struct from...
Sometimes I get random JLinkARM DLL unknown error when I reset my device. I tried different PC, debugger, supply of chip. Nothing fixed this issue.
NRF52840 REV 3
nrfjprog...
Hi Nordic
Please explain the use of signals VDD_nRF_SENSE and VSENSE_SW_OUT in the circuit.
The board version I bought is PCA10095/0.11.0/2020.50.
Thank you.
Hi,
I just noticed that setting any of the CONFIG_BT_CTLR_TX_PWR has no effect on the range and RSSI while advertising. Does this config actually do something? I tested...
hello,
I have a DHT11 temperature and humidity sensor connected to Raspberry Pi 4 B. I want to transmit this data from this raspberry pi to another node using 802.15.4....
Hi,
In nRF5_SDK version 15.3.0_59ac345 with nRF52840, the function nrf_nvmc_write_bytes() writes to the same 32bit word too many times.
According to the datasheet:
...
I am starting the Academy SDK course and getting my tools installed. I have VSCode installed (I have used it on many other projects and the "nRF Connect for VSCode" is installed...
Hi ,
When I set CONFIG_TFM_PROFILE_TYPE_NOT_SET=y to disable TF-M minimal mode, KMU SLOT MKEK must be empty right? When the KMU is not empty, the app will enter the tfm_hal_system_halt...
Hi! I have a Thingy:91 v1.6.0 and doing some current measurement on the device. I've disconnected the LiPo cell, and feed the Thingy from an Otii connected to the P3 (Li-po...
Hello,
I have a motion sensor with me and it has 4 pins. VIN, GND, OUT1, OUT2. OUT 1 and OUT 2 gives output voltage of 3.3V or 0.3V depending on a motion. I want to read...
