Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hello,
I'm having an error with the 832, specifically I'm just trying to port code over from an 833 project. I can compile no problem, but when I go to write I get
ERROR...
Hi there,
I've been working on creating a nice wrapper around the nrf modem library in Rust. Currently can be found here: https://github.com/diondokter/nrf-modem
When...
I was testing out the custom application from android studio, and have discovered that, for example, when using the rscs example my application does not see the device and...
Hi Nordic. This is a general question and could as easily have been posted to stack overflow but I have found the members and staff of this community so helpful and adept...
HI,
I am working on a application which has an requirement, that I need to read the current value if it is above threshold value then I need to turnoff the control. Here...
The executed command at connectedhomeip/examples/lighting-app/nrfconnect: west build -p -b nrf52840dongle_nrf52840
The messages i encountered:
...
/ncs/zephyr/include...
good day,
is there a way to set a gpio when in dfu mode? wanted to make GPIO 19 of nRF52832 HIGH during DFU mode because we assigned it as an enable pin.
in DFU mode,...
Hello,
I have my own custom board with nRF52832 and a NB-iot module SIM7080G that interfaces via UART.
I can easily program the device through SWD using J-Link. I am even...
Hello,
I am using flash_write_protection_set function with few low level function call for accessing extremal flash with nRF9160. And because of that I am facing one warning...
Hi,
I am programming the nRF52833 and using NCS v2.00. I have recently programmed the Peripheral Coded PHY to the board. I am using a Google Pixel 3 with nRF Connect as...
Hi,
Can we use the PPK2 kit for measuring current consumption in any other reference design board from a different
vendor which is not same as DA. The other vendor does...
Dear person in charge.
Before using PPK2 for a evaluation of current consumption, I checkd power supply vs corrent measurement by using PPK2 and 5kΩ chip resistor.
I...
Dear All,
I am building an application that needs to use NB-IOT and if that is not available then use LTE-M. I tried sending this AT Command:
AT%XSYSTEMMODE=1,1,0,2
...
When building the Matter Light Bulb sample application for the nRF52840 fails with:
/opt/nordic/ncs/toolchains/v2.1.0/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm...
What is meaning of error code 0x3004?
The following is source code of calling sd_ble_gap_tx_power_set().
int _gapTxPowerSet(const int8_t txPwr) { ret_code_t errCode;...
