Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
We have an application where we need the PWM pin state to revert to high impedance between bursts. It doesn't appear this behavior is capable by default. Is there a means...
Hi,
As mentioned in the question, I want to use the external clock as the RTC instead of the internal clock. How to configure it?
Platform: Windows 10
NCS version: 1...
For a fully connected set of node devices in a BLE mesh network, where any node device can send data packets to any other node device via an optimally short number of radio...
Hey,
upon a BLE_GAP_EVT_ADV_REPORT I call the following function:
static void pass_adv_data(ble_gap_evt_adv_report_t const *p_adv_report).
The function checks the p_adv_report...
Hello,
I'm having trouble setting up CMSIS Configuration Wizard in SES IDE v5.50a on Mac OS.
I've followed the instruction in https://www.youtube.com/watch?v=b0MxWaAjMco...
hi Team,
working Environment:
nrf52832 DK, SDK 17.1.0, keil IDE uvision 5, Windows 10 pro.
i am working with ble_peripheral based ble_app_uart example.
this program...
I am working on some teching modules covering MCUBoot and DFU ... and trying to get the
basic examples built for an nRF52840 DK board ... and am running into an error along...
Hi,
i am using MCUBOOT + nrF5340 and i am using the nRF Connect Device Manager to upload firmware and perform the upgrade.
I would like to know if it is possible to execute...
How do I check to see if a peripheral is inside the list of bonded units of a central?
I know I can just scan -> see unit -> connect -> change security and if it IS bonded...
Tried debugging and found the code loops in this place, lfclk_spinwait
I have added the following configuration in prj.conf
CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC...
With our nRF52832/52840 products, the UART sometimes drops characters.
I'm using nrf_drv_uart (SDK12) with two, one-byte buffers, and an interrupt called when data is received...
Hello,
I want to use app_simple_timer as a counter - I am trying to access the current number of ticks at regular intervals, something in the style of what was suggested...
Issue:
nRF Terminal does not connect to the device and does not produce any error. Once I click the RTT Terminal button (Under Connected Devices) in nRF Connect for VSCode...
Hi everyone, I am attempting to integrate buttonless secure DFU into my existing firmware application. I am following this guide: https://content.u-blox.com/sites/default...
