Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello,
I'm currently trying to convert the SPI example project for NRF52811 for the EVK BMD-360 and ran into an issue.
I'm using segger embedded studio 5.42a and nrf sdk...
Hello Nordic Dev Zone,
I have been developing on the nrf5340pdk and recently switched to the nrf5340dk.
I utilized the COM console output for app/net cores via the `minicom...
Good day,
I have successfully implemented exercise steps 1 to 5 of Exercise 2, Lesson 3 of the DevAcademy "nRF Connect SDK fundamentals" course, that deal with "adding custom...
Hi,
As i2c communication + computation takes 45ms in my timer interrupt that happen each 100ms and gave issue with SD, I decided to set a flag in the interrupt and execute...
Is there a configuration / sample available of mqtt simple to talk to the mosquitto server using an authenticated client on port 8884? I saw a message on here that was about...
Hi,
I want to get the GPS value from A- GPS continuously.
Meanwhile, if there is any new application firmware version update,
I would like to download the image with...
I see the problem here. use the dfu-util command in the window system
and i tried many methods and failed The following is my reference website
http://zadig.akeo.ie...
I've been playing around with some code that puts my hardware into System OFF mode to save power, and then will exit this mode and start up when one of three different GPIO...
Hi,
https://github.com/NordicPlayground/nrf52-ble-app-uart-c-multilink
I have tried the example you modified. It works fine. However, I get ERROR 17 NRF_BUSY when 2-3...
Excited to have ordered my BLE Audio DK which uses NRF5340.
In my use case I am looking for many microphones (audio transmitters) to a single listening device (audio receiver...
Hello!
I am working on a medical device project utilizing nrf52832 microcontroller. We use a mobile app to control and interact with the device through BLE since the device...
Basic Bluetooth connection question
How do advertisements usually work? So I have earbuds and a phone. When I pull the earbuds out of the case they auto connect to a bonded...
Hi All!
I am using nrf52820/33 and am able to successfully connectable advertise (coded PHY) by nrf5 SDK. Now I want to use NCS (Zephyr RTOS) to do the same job . Can...
Hi! I'm trying to use the nRF Connect App on a M1 Mac. I keep getting the error shown above with my Jlink connected.
This is the output of the nrfjprog cli tool:
How can...
