Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I developed a custom board using nrf52810-qfaa, i edited pca10040e-s112(sdk17.1.0) and changed the advertising led to BSP_BOARD_LED_3, as i have only one led on my board at...
Hi,
I am trying to debug ESB packets with the following setup:
1. PRX (NRF52810)
2..PTX (NRF52810)
3. Sniffer (NRF52832) ( modified PRX so that it returns without...
hi ,
i am developing a zigbee network and i have used the the sample project of zigbee light bulb, switch and coordinator given in nrf5340dk. now i am facing issue with...
Hi,
I am using the nRF52840 DK to connect to an external board via the P20 shield debug out. I was wondering if any indication is given if a board is connected correctly...
The linker script for the example code "Secure bootloader ble" for pca10040 have the FLASH section defined as:
FLASH (rx) : ORIGIN = 0x78000, LENGTH = 0x6000
According...
Hello,
I am using nRF5340 with NCS1.7.0 and nRF RPC lib for intercore communication for our product development. I followed this example ( https://github.com/nrfconnect...
Hello,
I installed NCS 2.0.0 via toolchain manager (Windows).
However, if I:
open a new cmd window
set ZEPHYR_BASE to <ZEPHYR_NCS_2_0_0_PATH>
try to build an example...
Hi Team,
I'm using a nRF52810 board for my project but in that when I upload code using development kit, at that time my device give advertising and what I gave task.
...
Hi,
I am using the nRF9160 on a custom PCB, SDK version 1.6.1 and modem FW 1.3.1
My Application uses MQTT to send messages to a server at regular intervals. In between...
I've just installed a new version of nRFConnect for Desktop, version 3.11.1. When I try to launch Toolchain Manager, I get an error "Unexpected end of JSON Input" error message...
Hello,
I would like to know why Matter cluster Simple Metering (ID : 0x0702) it is not proposed by the ZAP Tool and by the CHIP Tool. How could it be possible to use this...
Hi - I am unable to commission my NRF-5340-DK as a Matter device using the Android Chiptool app.
I am using the matter sample Light Bulb with v.1.9 of the NRF SDK. The sample...
Hello,
I have been working on the QSPI DMA encryption. As QSPI DMA encryption enabled, I noticed that QSPI cipher may use the flash location information to encrypt/decrypt...
