It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
In Nrf_SK_for_Thread_and_Zigbee, for openthread mtd, we used to define thread configuration in following code:
So to use node as SED (sleepy end device) we would...
Hi guys, I am fairly new to nRF and I try to understand the ways that data can be displayed to the terminal emulator.
So far, I have noticed that there are four different...
Hello there,
I'm starting out on the nordic platform for the first time but I'm running into an issue. When I try to flash the nRF9160 SiP modem firmware with the latest...
Hello
After building the whole environment of Zephyr and the rest, I downloaded the Serial_LTE_Modem build_nrf9160dk_nrf9160_ns example under Segger IDE to nRF9160 (PCA...
We are using public MAC that was purchased from IEEE (20 low bits are available for us to set and the upper 28 bits are constant to value assigned to us by the IEEE).
We...
Hello Community, I'm using the current sensor INA219 with NRF5340dk. Communication is through i²c protocol and using nrf SDK v1.8.0 . I'm trying to get the data output (Bus...
Is it possible to override ZEPHYR_BASE when building with the nRF Connect extension in VS code?
I am using workflow 4 (application as manifest repository) and can build...
Hi DevZone.
We have problems with our NRF52833-DK We believe they are damaged because under normal conditions, they normally draw less current (.001 A). It is normal to...
Hello Nordic. I'm using the nRF9160DK and with it, some sensors and an sd-card. I save data to the sd-card using a fatfs filesystem, the files are of magnitude 500 kB. I want...
Is the button (from Thingy52 black case) the only option to trigger an IFTTT? Can I use the sensor's information to trigger an event with the IFTTT? like if the temperature...
Hi,
I am merging a PWM_driver example with a ble-peripheral-blinky example to generate PWM signals with user-defined arbitrary phase-shift and duty cycle.
I am done...
Hello,
I have nrf52832 platform and my version of softDrive is (nRF5_SDK_15.3.0_59ac345).
My problem is regarding GPIO configurations are NOT retained ,when the nRF52832...
Dear Support term:
The Restful of Nrf Cloud is not work.
The node should have more that 100 data, so get ListMessages should give us pageNextToken.
Yes the result give...
Hi all,
I am using a custom board with NRF 52840 with SDK15.2 as slave and STM as master. I cannot receive right data, but the data to STM is right.
The above are...
Hi,
I am using an nRF52833dk to run a simple async SPI transceive API using k_poll My code is as below, for some reason it always returns BUS FAULT error Code:
Error...
