Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
1. I want to put the nrf52832 into deep sleep mode for some amount of time.
2. Once it wakes up from deep sleep mode, will it affect the content of RAM or flash or any system...
This sounds like very n00bie question and I'm a bit embarrassed to ask this, but I'm not getting anywhere so I have to ask it anyway. Why my GPIOTE events are not working...
we have high current consumption when we are using Accelerometer lis3dh with SPI with no transfer at all on SPI
We have 2 SPI’s in the circuit. The first SPI is connecting...
Hi, I am using nRF5832 DK. Currently, I am using SoftDevice s132 to compile my code. I want to compile it with a different SoftDevice (say s112). But it's not working. Kindly...
Hello, We are developing a smart padlock with nRF52840 on Raytac MDBT50Q-1MV2. It will be powered from CR2 type battery. We will support two types of battery chemicals, Lithium...
My minimum requirement is 1568kbit/s .
I try the example that in Nordic\ncs_v1.7.1\v1.7.1\nrf\samples\esb ..
I increased the dynamic load to 252 ,and It can send about...
https://github.com/NordicPlayground/nrf5-calendar-example
I run the above calendar example in nrf52840 and it run successfully with no error or warning, but i did not see...
Hello,
I am using SDK1.5.1 with one nRf5340 as central and another nRf5340 as peripheral. My use case is, I am setting security level 4 (BT_SECURITY_L4) after establishing...
Hi all,
I'm recently working with Nordic devices (more precisely nRF52840), so I'm still learning. I'm working on a project where I have a shared SPI bus with several devices...
I want to open memory window to check the flash area data which has been written when I was debugging with Visual Studio Code but I can NOT find and open the memory window...
Dear DevZone:
I am working with the nRF9160-DK board and I am interested in the following:
1.- Can I implement a VPN communication with this device? 2.- Do I need additional...
Hi,
About the function : nrf_fstorage_write(nrf_fstorage_t const * p_fs,uint32_t dest,void const * p_src,uint32_t len,void * p_param);
I customized an array of data ，but...
I am doing a ble project with three roles exist simultaneously, slave, scanner and broadcaster. i used the 'ble_radio_notification_init' and a rtc to see when the radio is...
Hello Devzone Community,
I'm a couple weeks into learning, working with Nordic ncs, Zephyr RTOS and west and friends. I'm working on an out-of-tree driver, and am stuck...
