I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
I'm trying to duplicate the boot behavior of a Thingy91 on a custom board, i.e. SW4:BOOT and SW3:BUTTON on power up, but the switches available use different IO. I'm wondering...
Hello, I am pretty new to using the Nordic products and was wondering if there is a simply way to write a text file from the nRF52840 to a pc. The system is required to log...
Hi Guys,
I know there are a lot if topicks about issue with "sd_softdevice_enable". I read them all and nothing help me. I'm using Eclipse IDE.
Im using a nRF52840-DK...
Hello,
I have recently switched my OS from FreeRTOS to embOS. I am now replacing the SDK files so my project will not be using FreeRTOS. I replaced the file app_timer_freertos...
hello,
I am trying to learn how to use the nrf52480 dongle and am trying to run the ble_connectivity example. I built it using Segger as is, no changes from the pca10059...
Hi!
I'm trying to sniff BLE advertising traffic using nRF Connect for Desktop on macOS and a nRF52840 Dongle.
I am running nRF Connect Desktop 3.8.0 on macOS Mojave 10...
I have done everything to install the VS code, installed Connect, Toolchains, SDK, Seggers etc. as in the help, but this is the result in VisualStudio Code:
It just keeps...
Hi,
The following code has been working fine since it was taken from the examples (NRF52840).
We wanted to remove the app_usbd_event_queue_process() so we enabled these...
Hello,
I have beacon advertiser and scanner. Scanner is scanning the devices from around. But its not scanning the device that i used for advertising. On the other side...
Dear Sir,
for my nRF52840 application made with the SDK v17.0.2 and S140 Softdevice I'm adding the peer module to a peripheral device example (UART with SAADC with timer...
I was trying to create my own sdk_config based on "$NRF_SDK/config/nrf52840/config/sdk_config.h".
I noticed it contains both the "NRFX" config and "Legacy" configs.
For...
I would like to change the GAP_DEVICE_NAME defined in nrf_mesh_config_app.h by DIP switch. like "nRF5x Mesh Light 1" or "nRF5x Mesh Light 2"
I have modified the light_switch...
Hi everybody, i get this error on a nrf53 with hr_coded on network coded, and UART example modified with multilink and coded_phy, tested by me on an nrf52.
The issue is...
