Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
It seems like there is a problem with nRF Connect 3.7.0 with Toolchain Manager 0.9.3
When I try to open I get the following error.
I have tried restarting and reinstalling...
I'm having trouble connecting the Thingy:91 to LTE network.
I'm using the thingy91_fw_2021-06-28_7a076c22 example.
I flashed correctly the thingy91_asset_tracker_v2_nbiot_2021...
Dear Nordic team,
We are deveopping BLE & ANT enabled display. Because it is a mass production product we need to do an automation for asigning devices destinguesed ID....
Hi, Dev Zone.
thanks for help : )
i'm try to porting DK Board's ble Boanding function to Target Board.
DK is working success.
refer to 16.0.0 SDK and 7.0.1 Soft...
Hi,
I am currently working on updating the examples/dfu/secure_bootloader_uart_debug example in SDK 15.3.0 to do an internal dfu on my nrf52840 DK rather than having the...
Hello,
Out application is using the time slot api to generate ~29ms (35Hz) burst of pulses.
Occasionally, the interval between two adjacent pulses extends to ~35ms ...
Dear Nordic support,
I need to clarify a few points using SAADC for battery measurement - running the ble_app_proximity application without modification. I measured the...
hello, i hanve a problem when i use usb transfer data to pc with ep1, sdk 17.0,nrf52840dongle
I have many data(more than 100KB) transfer to pc,when I send the data for once...
Hello,
I am using the nrf52840 for the application, basically i want to use the timer driver in my code.
so basically if i have 5 timers of nrf52840 and i am using one...
I am using a nRF52840 Development Kit to flash a custom board with a nRF52840. When I use the nrfjprog -p (or --pinreset) option to reset the CPU, it will consume over 1mA...
I am using nRF52833 on ncs to turn on the extended broadcast. After referring to the corresponding settings, I found that the transmit power setting does not take effect....
In standard sdk 17.0.2 is it possible to know which devices did i accidently disconnect?(Interactive command s140)
for example
my central is the interactive command...
Hi, I used NRF52 DK and NRF Connect SDK 1.6. I used the st_ble_sensor sample with no changes. When I press Button 1, I expect to get a notification on the central device....
Is there a straight forward guide that demonstrates how to changes the Asset Tracker V2 application from "Active Mode" to "Passive Mode"?
Referencing the notes on the application...
