Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
When the program runs, it will enter the hardware fault，because part of the code is lost in the program storage area of flash.
As shown in the figure, the left part is...
I want to implement lwm2m, and I use nRF Connect SDK v1.4.99-dev to compile the thread firmware.
I am using 52840DK, here is a screenshot of my project creation
No code...
Hello,
I had encountered framing errors when running automated tests that utilize UART CLI in my main code base. Currently what the test does is it sends a CLI command...
Hello,
I am using a nrf5340pdk board and I want to connect a sensor using I2C.
Which pin numbers of the board can be used for the SDA and SCL connection?
Do I need to...
I'm transitioning from nRF5 SDK to NCS and using Segger Embedded Studio (SES).
When using nRF5, SES gives options for the Compiler, including saving the Preprocessor output...
Hi,
I'm getting an error while trying to update the modem firmware (mfwnrf9160121.zip) on my thingy91.
I'm using nrfConnect Desktop on Windows 10, I activate DFU mode...
Hi. I am currently using the nRF52840 DK board and using the SDK 17.02.
There is our software engineers who are working on the heart rate service app to modify to suit our...
Hi,
I just got Thingy:91, and I was trying to see the response for a simple hello_world (found in zephyr\samples) application from Thingy:91.
Thingy:91 got programmed...
Hi,
Are LTE-M efficiency/TRP/TIS results of the nRF9160 DK on-board antenna available? In case there are several DK revisions available, does the version affect antenna...
Hi,
I am trying to understand how to enable SPI in blinky application provided by Nordic. My intention is to transfer data between the two Nordic development kit running...
I have advertising in s130 set to BLE_GAP_ADV_TIMEOUT_GENERAL_UNLIMITED. The idea is to advertise until a connection event is received. In reality the user will pull the finger...
Hi ,
1. I learned from Nordic FAE that on the nrf9160 module, 10 minutes after the edrx mode, the nrf9160 module automatically powers off the sim card to save power,
2...
Hello Team,
I want to use scheduler to schedule two tasks i.e task_1 and task_2. The task_1 and task_2 are as follow:
void task_1() { printf("Task 1 ran"); }
void task_2...
Sorry this might be a stupid question.
We are evaluating some modem to develop a IoT device, NRF9160 comes up to our list as its tiny size.
In the design of IoT device...
