Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hello,
I've been starting to get into level 0.1 programming after being able to loosely control an LED with GPIOTE and a timer interrupt using examples and API references...
Hello everyone,
I want to measure current of the whole board, I follow the instruction of nRF52840 DK , which suggest not to use the USB connector to power the board.
...
I am using Rowley CrossStudio 4.4 to debug my project. I can program and step through the code just fine, but I can't seem to get any debug out put on the Debug Terminal....
(1) Production Programming using CLI:
We are entering pre-production for a design containing an nRF52810 (on Rigado BMD-330 module), and we need to know what the CLI command...
Hi,
I was referring the timer example code for PCA10040. I wanted to include the timer code in my ble peripheral code which uses custom GATT service. Can you help me with...
I see that the nRF9160 DK has both cellular and BLE capabilities because it has both a nRF9160 SiP and nRF52840 SoC. Wouldn't it be optimal to combine both cellular and BLE...
Hi There,
The attached image shows the part of the schematic responsible for the enabling of the QM14501. I was wondering if there was a particular reason that the mosfet...
Windows 8.1, 64bit PC
I have a nrf52840 app that works from "SEGGER Release 4.30 Build 2019101800.40379 Windows x64" on the DK 16.0.0, and from " nRF Connect for Desktop...
Hi there,
I want to implement the BLE dfu in nrf zigbee and thread sdk but there are no examples provided in the sdk and if i try to use the files from nrf 52 SDK for...
Similar to this ticket , we are no longer able to connect to Verizon using a Hologram SIM after upgrading modem firmware from 1.0.1 to 1.1.0.
I'm attaching a matching console...
Inside gps_controller.c
We issue the following instruction to begin searching for a satellite fix.
k_delayed_work_submit(&gps_work.work,K_SECONDS(CONFIG_GPS_CONTROL_FIX_CHECK_INTERVAL...
Hi,
We are atempting to get DFU over UART working in our project, but there does not appear to be a bootloader project in the 16.0 SDK for this configuration. What would...
Hello, I want to put extra authentication when device is preparing for boot loader. I found callback "ble_dfu_evt_handler". I think inside case BLE_DFU_EVT_BOOTLOADER_ENTER_PREPARE...
