void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hello,
We're using the UDP/IP/6LoWPAN layers as provided by the nRF5 SDK 15.0.0.0.
After experiencing sporadic issues in communication we have a question regarding the...
Hi,
I am using BLE_Blinky_Peripheral example from SDK 15.3.0 with s112 softdevice. I want to use basic softdevice APIs instead of nrf_sdh libraries for enabling BLE stack...
I am a beginner trying to get a device to operate optimally under a battery. Where can I find a starter code template that would shutdown/disable everything, putting the device...
Hi there,
I am working with the NRF52840 Dongle and have been trying to verify what sort of influence other processes on the chip could have on the radio. Specifically,...
Hello Nordic team,
I'm having some trouble with discovering the characteristics of a custom device.
The peripheral device has a private service with UUID 06000002-0000...
I'm busy implementing a (serial) DFU host, but sofar i'm unable to send a proper init packet.
The bootloader keeps returning an invalid signature error
If i open a .dat...
I am using nrf52840dk
sdk15.3.0 and s140
I want to read a sensor data over uart and then advertise it but the advertising never starts after reading over uart even though...
IDE: Segger Embedded Studio
SDK: 15.2
Mesh SDK: 3.1.0
Im working on adding light lightness model to the mesh SDK and it requires doing an equation like sqrt(x * 65535...
Hi all,
I am working on a ble_app_uart sdk example thereby I can connect the bluetooth of nRf52840 to My mobile. I want to read the temperature and send it to my Mobile...
Hi, I am attempting to set up a nRF52840 DK as a BLE peripheral, and have been following the basic setup instructions at infocenter.nordicsemi.com/index.jsp . However, when...
Hallo everybody,
I successfully implemented on the NUS example the Pairing with the Passkey with the following Peer Manager configuration without LESC.
and the BLE...
I've written a DFU client in python. I'm trying to add the ability to restart a failed DFU without having to resend the whole file. I can see that the init packet is saved...
I cannot find an example project for using the PDM module on SDK 15.3.0. Can you please direct me to where I will be able to find such an example project?
Thank you.
HI,
i am using nrf52840.i am sending 500bytes from peripheral to central with the time interval of 100 millisecs. for 5 minutes its working fine,but after 5 minutes the...
