I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, I'm working with nRF52832/nRF52840 and SDK 15 or 15.2 on Windows with Segger Embedded Studio.
Is it possible to use the device in low power mode, but keeping active...
My nRF52840 Dongle appears to have failed while its boot loader was being updated, the led does not flash red like it used to and only gives a short white flash on plugging...
Hi, everyone,
We are developing the BLE project on nRF52832 chip by using RTT / UART logging. Previously we monitored the project via UART communication port. But than we...
Dear Team,
Can you please review the attached schematic of NRF51822 used with matching Balun and chip antenna.
Balun: 2450BM14E0003T
Chip Antenna: 2450AT18A100E...
I have an application running on an nRF52 with the S332 softdevice which is a server which exposes a a few services each with a few characteristics. I am using the Nordic...
Can the nRF2460 be operated with TXLAT (0x52) set to a value lower than 4 ?
Can the nRF2460 have a lower latency than 20mS ?
The range requirements are very small (30...
Hi All,
I have created a custom board header file based off of the pca10040.h file. I have customised this to support 10 buttons and 2 leds. I have also extended the array...
Hi everyone ;)
I have a problem with timeslot ESB library with Bluetooth LE. In my application i need do somethingh like that:
Bluetooth and ESB PRX works excelent...
Hi, I am using the BLE mesh 2.2.0 with nRF5_SDK_15.0.0_a53641a. I am using Segger embedded studio as toolchain. I was able to compile and flash the default app code onto NRF52...
I am working on an application to connect approximately 500 devices in a single network... trying to check if Thread or Mesh is a better option... Please do suggest...
After searching around a little bit I found this post, but sadly an answer did never come up apparently. I'm using the nrf52 DK, using the 132 Softdevice.
I'm kind of at...
Hi every one!
I have nRF52840 dongle and BMD-300 Series Evaluation kit featuring the nRF52832.
I`d like to transmit continuous signals from nRF52832 to dongle(Desktop...
I have two ble boards（board A and B）, one for client(Board A) and the other serve as slave(Board B). now i want to use board A to upgrade the application of board B by OTA...
