void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hello,
We have the following Problem to solve in general:
A device should control the exhaust system in a vehicle.
This device needs to retreive the engine RPM using a...
Hi
I have a brief question to which I'm not able to find a clear response: When the SD send a notification of a change in a service value, this notification has a confirmation...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Hello,
As far as I can tell, the NUS app sends a signed char of value -127 to 127 in decimal. Is there a way to use the stock UART application to send an unsigned byte...
Hi Noridic,
I follow the Application note Nan_36 and download the nrf51-ble-app-lbs project as a practice, but the compiling is not smoothly with SDK 9.0. I finally fix the...
Hello,
I am working with S110 stack and the custom application. I wanted to use the ADC driver with blocking and interrupts enabled. But the application is blocking and...
Hi, I use NUS quite alot with the following condition;
(SDK 7.2 & S110 7.1 with IAR 7.1)
When the peripheral only uses NUS, iOS cannot detect the peripheral at the ...
Naive follow up to What is NUS? .
Is NUS merely a vehicle for tutorials and fast prototyping? Or can it be used to build real world apps on?
If so, do we rename the...
Hi All,
We are in design phase of our project . We would like to use NRF52832 for our project.
Our project is a wearable based on BLE. We are planning to use RTOS in NRF52...
I am starting to port the example
nRF5_SDK_11.0.0-2.alpha_bc3f6a0\examples\ble_peripheral\ble_app_hrs to my board. I haven't made any change to the example to save something...
Hello, I have a problem when I attempted to increase timeslot length with 10 ms ,every time I received NRF_RADIO_CALLBACK_SIGNAL_TYPE_EXTEND_FAILED signal.
Why can't to extend...
I use nrf51822qfaa,s110 v8.00,keil MDK IDE.
If the program is wrong,The chip will reset,
I want to save some data to the FLASH area before the chip reset.
What I need to...
nRF 8001: How to use it in Beacon mode where in no pairing or Bonding is required and
it only transmits some information which cn be received by any phone that comes in range...
