I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I know that a lot of question exists on that subject, but I can't manage to have an accurate battery measure on [Nordic Beacon device] (battery CR1632 3V) ( www.nordicsemi...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi,
after reading the nAN-36, I tried to write an application for the nRF51822, with the custom Led Service provided with nAN-36.
I take as a base the Nordic HRM application...
Hello!
I'm using the evaluation kit and i have two questions: firstly, I'm trying to make up a program that allows the communication between two modules, on one side a glucose...
Hi,
I work with Master Control Panel 3.6.0.8331 on x64 Windows 7 and I noticed something weird. When device name of a connectable peripheral device consists of numbers...
Hi!
I'm testing a custom service developed on the nRF51822 development board by using the Master Emulator API in a C# project.
The project is based on the example project...
Hi,
I'm trying to set up Keil uvision to debug my nrf51822 mbed board.
I've exported a uvision zip file from the mbed IDE to test with.
I've installed the following...
I am fairly new to the embedded world and I have my development environment setup and running with the other samples but, I'm interested in the 130 softdevice. I have the...
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
i would like to know what the logs mean in MCP log file,.
AS follow:
3563;11:19:08.9590 [480108198][ReadPacketQueueThread] Serial port read: 02-00-20-14-00-10-00-04-00-1D...
Is there any possibility to detect active state on the more than one pin using sense mechanism? GPIOTE_IRQHandler is blocked when it detect active state on the one of the...
Hi,
Is there any reverse polarity mechanism inside the nrf51822 IC?
If externally we don't use it, and user connect power supply in reverse way, what will happen with...
Hi, and thanks for reading this, I'm currently able to power the PCA10005 by sending 3.3v to pin1 of p2, and pin5 of p2 to ground, with this setup I'm able to program the...
