Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi. I wrote a firmware on nrf9160(SIAA chip), but it doesn't work. On the hardware side, the circuit is same as that of nrf9160-DK, CTS and RTS is short respectively.
If...
Hi,
We are using two nRF54l15-PDF to communicate as SPI, one is in master mode and one is in slave mode. The master device sends a simple array of bytes, the first one being...
Hello,
I'm currently working on NCS2.6.0 and ANT sdk v1.3.0,
I would like to know is it possible to do BLE scanning(without connection) and ANT+ heart rate searching at...
I'm working on getting a radio test example project built for our custom board that is currently in production in order to perform some FCC testing, but I'm struggling to...
Hi everyone, this is more of a programming advice question: basically we have a "registration app" associated with our BLE product which will be used to communicate user details...
Hello,
I've been developing code on nRF9160 for a while. In the beginning everything was straight forward and working just fine also the code was pretty simple. Now like...
I am currently working with the nRF5340 and using NAND flash for data storage. With the current code size, I need to create a secondary partition in the external NAND flash...
Hi,
I am using nRF52-DK to program a custom board based on BC832 (nRF52832 SoC). I recently updated "nRF Connect for Desktop" and associated applications. I believe some...
Hi there,
I'm trying to get the entire toolchain running on a new Win 11 AMD machine. Visual Studio Code has version 1.88.0, toolchain has v2.6.0 and SDK v2.6.0.
Therefore...
Hi,
i am working on Pancake motor C0820B006F circuit and it is connected to P0.12 pin and ground iam usin NRF52 development board. i want to change the pan cake vibrator...
Hello
We developped a firmware on the nrf52840 dongle able to communicate with a Windows PC through the USB.
On Windows 10, we can communicate with a serial COM port....
Hi, we looking at converting our devices from a BLE communication protocol, to BLE LR with MESH networking.
Currently, we are doing the following:
Android tablet connects...
Hi,
we are ramping up production, and need to make many production jigs, and programming in parrallell since the programming of the modem takes 1 min +.
We are using an...
I am using nRF52840 Dongle as RCP with RP4 as OTBR and its working fine.
I have compiled sample/openthread/coprocessor as RCP using VS-Code. When trying the same via 52840DK...
