I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
I'm trying to use the ADC on the DK52 (PCA100040) to sample and transmit data to a PC. I've been able to write code that samples data to a buffer and I've modified the peripehral...
Dear all,
I've got some problems with the uart implementation in the peripheral uart example. I am using nRF52833 DK and SDK 2.0.2.
What I need for evaluation is a device...
I've the following situation:
1. Send CoAP message trough send(), this causes the the nRF9160 to start RCC connection
2. Wait for RCC connected mode (LTE_LC_RRC_MODE_CONNECTED...
Hello!
I am in the process of adding OTA DFU support to our existing application. However, I'm having problems starting the DFU process.
For security reasons we want to...
Hi there,
We are using the nrf9160 DK with Serial LTE Modem (1.8.0) to run some tests on the modem (1.3.1). We are using the MQTT client AT commands in order to connect...
Good day
I am attempting to use lwm2m to post temperature sensor data. At the moment I'm trying to to initialize object with ID 3300 (generic sensor)but it is not appearing...
MacOSX 13.0.1, Intel. nRF Connect SDK v2.2.0 as downloaded by Toolchain Manager v1.2.1 from nRF Connect for Desktop 3.12.1.
Same happened with SDK v2.1.2.
Similar steps...
Hi,
I was trying to put the nRF5340 Audio DK board in DTM mode to test RF capability but couldn't find out any way to do so.
Please let me know if I can find some documentation...
Hi,
We have 3 nrf5340 Audio DKs we want to connect together. One of the devices is connected as central and the two others are connected as peripheal. By know, the two peripheal...
Hi!
We plan to build an AoA localization system with the nRF52833. To calculate the signal phases per channel, the antennas are connected to the BLE-RX via switches sequentially...
I am working on the nfc uart examples. first I found the poller example is not support for 10056 board. I make the change for that. code can build and flashed, but then I...
Hello,
My development requires new device binding and I want to share the steps followed and my issue.
My device is Renesas and commuicate via I2C protocol.
Based on...
Hi Team,
I am using nrf52840 controller and SDK 16.0. I have referred to the product specification manual/data sheet already. However, I would like to have the " programmer...
Hi,
We received the new nRF52840 USB dongles this week, however when we try to access the getting started URL on the dongle package the web page gives an error.
The...
