Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hi,
I am developing the nRF52833 DK with NCS 2.00.
I have successfully implemented a service to print the RSSI on the Android nRF Connect application. I use the function...
Hi all.
What is the best practice to set the system in standby? I have a PWM and when is active the system can be in a low power consumption until a button is pressed. But...
Hi,
I've some questions on nPM1100's buck regulator
1) What is the Iq (quiescent current)?
2) Does it support 100% duty cycle?
3) What will happen to VOUTB if VINT...
Hi,
We are using ANNA-B112 module with nRF52832 chip and trying to store the product serial number in UICR. From the description of UICR, it seemed that the CUSTOMER area...
Hi,
A have an application on a custom board that will not start, unless I use JFlash Start Application command, or attache the debugger. I already added CONFIG_BOARD_ENABLE_DCDC...
Hi,
given "nrf_drv_twi_xfer" or its "nrfx_twim_xfer" younger brother is used to communicate over I2C, and its a TxTx tranfer, than what does "nrf_drv_flag_tx_no_stop"...
I am using bleak and python to connect to a ble device and then using subprocess to run the dfu. The ble device disconnects when the dfu starts and then I get "Connection...
I have a Thingy:91 board that appears to be broken, no response either on the LED or via USB UART when switching on.
I've earlier done some development with it, and hooked...
Hello,
I am attempting to follow along with the AWS IoT example. Everything has gone OK so far (Create a Thing, Create a Policy, Create and download certificates) until...
Hi All,
In our product we have noticed that, on a few occasions, some important information that is saved using FDS (in a file with ID: 0x02) are being erased when an OTA...
Hi,
Do you have a recommended circuit for supplying VDD_GPIO with the right timing relationship to VDD?
Section 11.1 of the datasheet says "VDD_GPIO should be applied...
Since the 9160 will vary his transmit power based on signal strength, is there any way of determining what power is being used for a given transmission? I know that the max...
The Edge Impulse firmware compiles and flashes to the Thingy53, without problem. I would like to increase the range of the BMI270 accelerometer, but can't find any reference...
I am using 52840 and SDK V14.2.0. When compiling nrf_ble_dfu.c I see the following error in nrf_dfu_types.h: line 258
"two or more data types in declaration specifiers....
