Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
https://github.com/nrfconnect/sdk-nrf/tree/main/samples/bluetooth/nrf_dm
I used the demo linked above to test RTT and DHCP respectively. Within two meters, I found that...
From the DF spec, we know that the connectionless AoA puts the CTE signal on the periodic synchronous adv, why, and what is the benefit. Is it possible to send CTE in extended...
Hi,
I am using nRF5340DK for development. Currently, I have two problems:
QS1: When I use fun nrfx_gpiote_out_toggle(), it reports Assert error on NRFX_ASSERT(! pin_in_use_by_te...
Hello,
I am working on integrating wireless-timer-synchronization into the HCI_RPMsg sample provided with nRF Connect SDK. My goal is to synchronize ADC sampling between...
Hi all,
I am using the kit nRF5340-DK, connecting to windows 11 pro. Already installed nRF Connect for Desktop 3.10.0 and nRF Command-Line Tool 10.15.4 (32/64 bit).
It...
Hi:
I want to include the Characteristic value in the advertising packet，for example the real time battery level，thus there is no need to establish a connection between...
Hello.
I wish to implement a DFU Client. One (USB connected) nRF52840 based device should update an other (Wireless) nRF52840 device.
As the SDK only has a DFU service...
I am planning on pairing two parts of my system using OOB pairing via a UART connection. I couldn't find many examples of pairing using a physical connection as oppose to...
Hi,
I use ble_app_uart sample code using nRF52840 in SDK15.
There is a code below in ble_stack_init().
And APP_BLE_OBSERVER_PRIO is defined as 3 at the top.
On...
Hi there,
We are currently doing current measurements on the nRF5340 DK with a Power Profiler Kit 2.
To do this, we simply use the PPK as a source meter and connect it...
Hello Nordic Semiconductor
I am developing a small application on the nRF52840 development kit where I need to transfer I2S signals in/out of the MCU. I have set up an I2S_IRQHandler...
I'm trying to send data readings an advertising packets from the nrf21540-dk board, and use the phone as an observer to record the data.
So far I've been able to send counters...
I'm sending a short data string from a NUS application. For some reason I cannot read the data as bytes, only string, even if the sent array is uint8_t.
Is there a specifier...
