Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hi All,
I feel like this question/topic has probably been discussed ad nauseum, but I feel like I'm not confident in the conclusion I'm drawing from other posts I've seen...
How to reject/disconnect peer (smartphone) which tried to write huge data to service? For now in my project (based on ble_app_multperipheral project from SDK) if the smartphone...
Hi Nordic Team,
I would like to understand how the radio test works. A better description of the commandos would also be helpful. Is there a more detailed description than...
Good evening,
The following link to "TIMER HAL" lists various enums, including for example " NRF_TIMER_BIT_WIDTH_32 (alias of) = TIMER_BITMODE_BITMODE_32Bit ". I've used...
On Windows 7 64 after update to 3.8 (and 3.9) nRF Connect for Desktop the Bluetooth Low Energy and Power Profiler can't find device nRF52840-Dongle and PPK2.
What to...
Hello,
I was wondering if I could bypass the protocols related to BLE transmission (GATT/ATT) and utilize the RADIO peripheral in a close to constant TX rate without regard...
Hello!
Short question: How can I pass a parameter to a SW Interrupt?
Expanded question: I want the board to wait for an ammount of bytes comming from SPI, once this is...
Hi all,
i am really desperate. since more than 1 week i am trying to work with the digital inputs in my custom pcb.
I can set all digital outputs, but from the inputs...
Hi Nordic support team,
We're using nRF52840 to develop a product with lots of features, using nRF NCS latest version (1.7.x as of writing).
Currently we're sitting at...
Hello! I'm working with the nRF5 SDK17 ( https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fble_sdk_app_interactive.html ), and I'm...
Hi nordic,
After I transplanted nrf52832 to nrf52833, the upgrade of nrf52833 failed, or stuck in the bootloader.I tried to use the current method to upgrade nrf52832, it...
Hi
Problem description：
In application serial_lte_modem ,When sending AT command "AT + CFUN?"， return"at_host:Error while processing AT command:",What caused this？Thank...
Hello,
We have a nRF52840 on our board, whose fw we would like to be able to update through both BLE and UART (the MCU is connected to a ST32 MCU via UART) using a bootloader...
Hello Everyone,
I am currently using the AGPS example on the nRF9160-DK with nRF Connect SDK v1.7.0. I notice it requires 4 satellites in order to provide a position fix...
Hi,
I need to use system tick to do some math calculate. So I create a new function to get systick like as below. then I can get some number.
And I create a 200ms timer...
