Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
Is it possible to generate a passkey before initiating the pairing process?
The peripheral in my system does not have a display or input, so I'm looking for a way...
Hello Developers, I am currently developing an application on top of mqtt-sn publisher example. Now i want to add OTA DFU in my mqtt-sn based application. I have started up...
Hi, dk:PCA10095 sdk:ncs v1.7.0 example:path:D:\ncs\v1.7.0\peter\11_hello_world_pdm_i2s
Download changes when I build the project using SES: Previously: Download code available...
We used the nRF52840 in some projects, but there are still some problems with the short bridge at the IC during production.
So we want to leave the blank layout of the unused...
HI
We have to try to develop a product with nrf5340. The product needs to be waterproof and also it made up of metal and a small amount of plastic enclosure. In that how...
Dear Members,
I want to run ANT+ code in my custom board,
It works well on PCA10056, I can upload softdevice and the code to custom board board,
but I didn't get any...
I've recently upgraded my SDK to 1.6.0 and I am now unable to read the state of P1.00 but I am able to read the state of P0.28.
I've stripped the project down to just a...
I recently installed nRF Connect SDK using the Toolchain manager. Install went through without any issue but when I am trying to open an example project in SEGGER Embedded...
Hello,
I have a nRF52840 and am unable to flash an application to it. I am trying to flash the "examples/ble_peripheral/ble_app_blinky/hex/ble_app_blinky_pca10059_s140.hex...
Hi Team,
What is the meaning of BLE advertising link encryption and data encryption,That makes no sense .In glucose example the DH computation is calculating can you clarify...
Hello All,
I configure ADC & BLE UART in one code. we are using 4 ADC channels. but I observed that there is a timing delay approx 2-3 sec to update ADC. we are using a...
Hi everyone,
I wanna implement the wakeup from SYSTEM OFF by button. The project is based on the ble_app_uart example. After receiving a command from BLE, nrf will go to...
All,
Before I head off on that experimental path, was wondering if anyone on here tried to parse and convert project.yml to Cmake arguments? We use ceedling for unit testing...
Looking to see if anyone has run into this issue and how it was resolved. We have a nrf52832 running sdk 15.3 (also tried 17) sd 132 6.0. We are using the pwm module + nrf_drv_pwm...
