Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Want to realize a function: stop broadcasting after a broadcast, update the broadcast content, and then start broadcasting again after the specified timeout. How can I judge...
I am using the nRF5_SDK_17.0.2_d674dde and the nrf5_SDK_for_Mesh_v5.0.0. I am using the nRF52 development kit and I want to know if I can use the flash fstorage on the mesh...
Hi. I am working on a project and am planning to offload most peripherals to the net core; a few are listed below. Is this a bad idea? I realize I might run out of flash memory...
hello ,
During my twim0 initialization, I have configured clear_bus_init as true and hold_bus_uninit as false. But i always get hold_bus_uninit as true.
then I dig into...
Hi!
We would like to install approx. 2000 pcs BLE devices in a mesh network. The device density is quite high (2x5 meters matrix, same level, no objects).
I think only...
I am looking for a automation where in the scripts should be able to send the CCCD(Client Characteristic Configuration Descriptor) response within one second.
1.Which tool...
Hi,
On a nrf52840 running SDK 17.0.2 and Softdevice 7.2, while being connected to two devices in central and peripheral role, I observe that on the connection where the...
I'm trying to see if there is a simple way to scan for ANT packets on all supported frequencies (not ANT+, which I know is on a single channel, 2457MHz). Just for the presence...
Hello, I am currently using the logger backend to send information via UART from the nRF52811 to a PC. This works well, but only for one way communication. I would like to...
I have nRF52840 dongles that have something already programmed on it. They are encased in plastic and I have no access to the little reset button. How can I install my SoftDevice...
Hi, I'm having trouble implementing DFU buttonless.
I ran the tutorial step by step in the following link: https://www.u-blox.com/sites/default/files/Add-NordicSemiconductorDFU...
Hi Nordic,
From some cases in the devzone, I know for nRF52 series, the ESB doesn't support 250Kbps mode.
One of my customer employ nRF51822 in their product, so I want...
Hi,
It seems that we are experiencing exactly the same as what is described in this topic by @kienasv. That topic seems closed for replies, and the solution has never been...
Hello ,
What is the purpose of the second line of the code in errata 89 ?
I mean this line ;
*(volatile uint32_t *)0x40003FFC;
did you use this one like nop ?
...
I need to install a BTLE application on an nRF52840 dongle that is enclosed in a case and therefore I do not have access to the reset button.
I have looked at some of the...
