Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
Is it possible to join an existing mesh network with a provisioner made on Nrf52840 (s140) ?
I have used the provisioner example to make a provisioner which actually...
Hi everyone,
I am working on a project, currently developing on the nrf9160-dk board. And I want to enable AWS and AGPS together in my project. And once I've enabled them...
Hi.
I modified the fstorage example to create the project.
I split Flash into three areas as shown below.
*Flash Area(0x26000 ~ 0x2ffff) : Bootloader
*Flash Area(0x30000...
Hello Nordic team,
We are making our own custom project, and we are facing problems in implementing lower power modes.
Reading from the info center, when the DK Board...
When initializing two channels, enter scan mode。After the two channels are converted, the callback function will be entered，Read conversion results。However, the requirements...
Hello
I am following a beginners tutorial on youtube and trying to implement simplest possible example of reading an analog value.
I want to use the nrfx library to do...
Hello,
I am working on a project where I am using 8 ADC channels on the nRF52832. When I run the code the device seems to get ADC values that look correct. But, if I pause...
I have an out-of-tree driver. It has an I2C that is working but also GPIO that are only working with compatible = "gpio-leds" but not with the driver compatible = "st,vl53lx...
On the nRF52840 there were many pins specified as "low frequency I/O only." Does the nRF53 have this same restriction? I don't see mention of these pins in the nRF53 datasheet...
Hello, I am working on application with nRF52833. What is max load current of internal LDO between VDDH - VDD? VDDH is 5V (USB) and VDD is 3.3V. There isn't anything about...
Hi
I am not busy developing an new product with nRF52840.
I want to use the BLE functionality and started with the ble_app_hrs sample application.
I download the pca10056...
Hi everybody,
I am trying install and set up Wireshark, i am in this step:
this is my output:
I think trhe problem is because of pyserial isn't detected, i have...
Hi,
I purchased a BLE dongle with your 3rd party HolyIoT: mini Holyiot-nRF52840-USB-Dongle. It is recognised on Nordic Connect, but not Nordic Programmer (Err msg: DFU trigger...
Dear devzone-team,
could you please tell me where the yaml files (like thingy91_nrf9160_ns.yaml) in the board folders are used?
I could not find a tool which evaluates...
