Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hello, All
I want to implement OTA using Thread with nRF Connect SDK.
Is there any sample code or reference this can be done with Thread?
Even if there is any experimental...
Hello,
I have a: nRF5340DK connected to Windows10 PC via USB.
I also have these that are working fine in terms of being able to communicate with the nRF5340DK over Bluetooth...
nRF SDK version is 1.5.1
upgrade modem fw to 1.3.0
Is there any way to do software reset on GPS modem? I have ran the gps example and I notice that "printk" sends everything...
I'm using the nRF5340 DK with the HRM example. My phone is HUAWEI mate 10 (Android 10).
I could scan the Zephyr Heartrate Sensor in nRF Connect App and nRF Toolbox App ...
Hi Team,
In continuation with Case ID: 269054, 269278
I am using NCS (as suggested) to avoid high current consumption happening during softdevice initialization.
I set...
Hi, I'm enthusiast of nrf5340 DK. BUT: in the samples I'm not able to find some viable openamp (other ipc seems to have the same problem) example. I am looking for a way to...
To the kind Nordic support team,
I have got a nRF52833 based Raytac module I'm using to develop before using a custom board.
I'm using Microsoft Bluetooth Virtual Sniffer...
Dear Hardware Application Engineer,
We are using nRF ASICs for our IoT products for the past two years.
In nRF52x series products, forex. nRF52840, there is a power supply...
When I do a DFU on my device (nrf52832 with Zephyr) using nrfConnect, the update is successful, but I get a message in the log stating "Length of data to send exceeds MTU...
Hi Nordic,
I am using the Raytac module with the nrf52840 inside, I have set my hardware as mode of Reg0 DC/DC enabled. Which disconnected the VDD and VDDH. Also I have...
Hello,
We need to use the RX TX on TTL level. That is possible with the nRF24L02 chip, as fa as I can understand from the datasheet. But we also need to use 8 bits, even...
Hello,
I am using nrf52840(nRF5 SDK v15.2.0). armgcc compiler, softdevice s140 hex, and application + OTA bootloader combined hex file.
in my application, I have some...
Hi,
We're developing with Zephyr OS on nrf9160 and recently added SD Card support. We build our application also for qemu_x86 for testing purposes and would like to add...
Hi!
Hope you are doing well!
I was wondering if we can use a normal characteristic to do the buttonless DFU (i.e. transmit all .hex file through that normal characteristic...
