Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
I am working on a custom nRF552832 board. I need to use the reset pin (p0.21) as GPIO input.
I am using the NRFConnect plugin on VSCode to develop and program the board...
Hello,
We are using the nRF52840_CKAA_R7 package of the nRF52840 on our custom board. The USB pin connections are designed based on the nRF9160-DK's nRF52840 reference....
I would like to be able to open a bash prompt with the nRF Connect SDK (NCS) v2.0.0 toolchain environment loaded without going through Toolchain Manager ("open bash" option...
We are evaluating the nRF5340 chip for a Bluetooth LE audio broadcast streaming application.
Is it possible to use adaptive frequency hopping with the BLE audio network...
For the RADIO peripheral of the nrf52(840), if you set up the radio to receive coded Phy transmissions, I have the opportunity where I can set the MODE for 125Kbps or 500Kbps...
I'm trying to use nordic's BLE sniffer on a nRF52833-DK. I have programmed it with the firmware "sniffer_nrf52833dk_nrf52833_4.1.1.hex".
I've then tried both the command...
When I use nRF Programmer on my laptop (v3.0.7) to update firmware on my Thingy53 with a USB cable and SW2, the programming seems to finish normally, but it prints "Bluetooth...
Hi, I'm having Bluetooth LE peripheral nus code which works fine with v2.7.0 with nrf52840DK (I can connect with an Android App and stream data etc): Changing the build configuration...
NCS 2.7
NRF52840
Building with sysbuild, MCUBOOT, and 2 different applications (mfg and end-user)
My custom board includes a sensor fusion IMU from bosch. The firmware...
Hello,
I want to test nRF21540 EK with a nRF5340 DK.
I am using ncs 2.7 , and don't want to use sys build . I want to use child image/ hci_ipc .
I modified ncs/zephyr...
We have devices that have low signal so they have to reconnect to AWS a lot. We have a watchdog timer with a 100s timeout that we feed every 10 seconds in the control loop...
Hello everyone!
I am having trouble with my current setup and I would like to ask you for your advice.
I am developing a central station featuring nRF5340+nRF7002. This...
I generated an overlay file with the following info:
and there is my main.c file:
However, when I tried to debug my code to understand what was wrong, I got the...
Hi,
I am using nrf52840 and implemented shell interface. I have testing it over uart and uart over usb. At any given moment it can be enabled over 1 interface in device...
