Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi while implementing/testing MTP on Linux Wireshark captured setup requests asking for "Device Qualifier Descriptor" according to section "9.6.2 Device_Qualifier" in the...
Hello,
Can you please provide information for current consumption of the GPS in these modes?
VDD=3.8V
Acquisition time = ? seconds
Acquisition current = ?mA
Tracking...
Dear all,
For our project we want to store information on the device in an additional flash partition. We have created a new flash partition, called factory_settings_partition...
Helo Nordic support team,
I am supporting a client that has designed a product using the NRF9160 with GPS. The product has a small patch antenna mounted on the pcb board...
Hello. I am trying to build an project and I need to use RF module. And I have to Use pic18f45k22 with MikroC. But I couldnot. I have some 18f45k22 codes but dont work I dont...
Hello,
I need to retrieve the IP-Address of the modem, are there any convenient way I can do this?
AT commands maybe?
Appreciate any info on this.
With regards...
Hello
I am having rather odd problem with SWDIO pin shorted to ground. I am using Fanstel BT840x BLE module and I have never seen this issue on my custom board until last...
I see this line for cache enable register in application domain : infocenter.nordicsemi.com/index.jsp
NVMC built-in cache not supported (ICACHECNF, IHIT and IMISS registers...
I'm trying to test button less dfu on nrf 52840 dk. i am simply compile that hex ble_app_buttonless_dfu_without_bonds_s140_with_setting_page.h file with soft device s140 or...
I am building the coded bluetooth gateway using nrf52840 and ENC28J60. Integrated between two examples:
https://github.com/nrfconnect/sdk-nrf/tree/master/samples/bluetooth...
Hi to everyone!
I am working (with Keil uVision) on a custom PCB that includes the NRF52832 (MDBT42Q module) and some sensors from MAXIM INTEGRATED. There is a Sensor Hub...
Hello, I was told to make a new ticket after commenting on this ticket .
I am using SDK 14.2, S140 alpha, NRF52840. Segger IDE. I have been developing with this IDE & SDK...
Hello
I want to transmit location data to website using udp, the examples udp and gps are very good and I need combine in only one project but dont understand what files...
Hello,
The product specification for the nRF5340 peripheral chapter here mentions " The application core peripherals are accessible from the network core".
However in...
Hello I am using ncs version 1.5.0 .We are using nrf9160 dk version 0.15.0 & 1.0.0 for our development.Whereas we observed some issues like the network latching time is getting...
