Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi everyone,
I'm using the nRF5SDK160098a08e2 and i tried to compile the ble_app_eddystone exampe but i'm getting this compilation error!
cannot find ../../../../.....
I am unable to read any uart input when I configure UART1 with nRF9160DK.
Please let me know if anything is wrong in my code/config
main.c
nrf9160dk_nrf9160ns.overlay...
In the Sleep mode and nrf52810 was Broadcasting with space 125ms once.
The normal temperature was good,that only 0.08mA. but why not 85℃，The current was up to 0.21 mA ,it...
Hello
I would like to detect timeout when I send a confirmable coap message not received.
My problem is that the response I receive in my response_handler is always...
Hello.
I'm going to make a prototype board and use it soon. I will make a prototype board with nrf52840 and use it soon.
It's my first time developing a prototype board...
nRF sniffer: v3.0.0
Wireshark: v3.2.6
Hardware: nRF52840 ( PCS10056 )
wireshark did not show packets with MTU greater than 20 bytes, is it still not supported?
Hello ,
We are using the following.
Module: Bm833 (nRF52833) from Fanstel
Softdevice: S140 7.0.0
SDK: nRF5SDK17009d13099
Sample code: ble_app_uart
We have added...
Hi, We are developing a BLE app on nRF52840. For the next step, we want to try reading/writing to other devices through connector interface on nrf9160 dk. Is it possible to...
I followed the steps below: flash softdevice flash bootloader
generate package
flash package
But after that I can't connect to this board by using usb and need again...
Dear Team,
I am totally new to NRF24LE1. I have bought 6 pieces it through online. Iwant to program it using HAL libraries. I've searched it everywhere I ca do. But I...
Hello, everyone.
I use the ble_app_uart on the nrf52DK board and SDK V17.
I would like to send data from the app using RX characteristics of UART service. The function...
Hi all.
I have written an application using a softdevice and I want to analyse an interesing behavior I don't understand at the moment. So I want to record a trace/log of...
hi!
Can anyone help me with code merging of saadc and ble uart.
Basically i have done analog to digital conversion of my sensor value and monitoring it on serial monitor...
Good day,
Studying the possibility of using C ++ on the MCU nrf52840, I met an interesting moment in file "nrf52840.h"
I have added a part of the file which gives me some...
Dear Nordic Semiconductor support team.
I tried to make my nrf51822 DK to talk to Micro:bit by using Gazell library. ( from nRF5_SDK_12.3.0_d7731ad\examples\proprietary_rf...
