Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hello,
After a long war trying to connect MPU6050/MPU9250 to NRF52 DK with nrf52832 on board, I finally succeeded and I am getting values through UART.
But I have 3 problems...
Hi,
I would like to get the stored CCCD values of a bonded peer using pm_peer_data_load()
I am currently struggling with the format of the data returned by pm_peer_data_load...
Hello.I am a graduate student at Nanjing University of Posts and Telecommunications in China.My question is, does your company provide the source code of the Bluetooth mesh...
To the kind attention of Nordic support team,
we are doing ble bonding using passkeys.
We noticed that when starting the passkey phase, a ble connection event is generated...
I am not able to run commands with nrfjprog using the J-link Segger device
e.g. nrfjprog --family nrf52
I can do it only with the Keil or Segger UI environment
How can...
hello
right now i am sending 100 plus data per second i want to print millisecond at each data how can i acheive this is there any program in nordic or github i can use...
Hello
I am working on SDK v17, using nRF52832 (MDBT42Q) and MPU6050 sensor. I tried TWI_SCANNER because I thought there was a problem getting the value of MPU6050.
However...
I am reading a thermistor voltage divider from Vdd using the SAADC with a reference voltage of Vdd/4 and gain of 1/4. I thought that this would track Vdd so I wouldn't need...
Hi, the provisioning works and after that the dk is capable to get mesh messages but oddly enough a restart brokes this feature.
The error message is:
0x0c means BT_HCI_ERR_CMD_DISALLOWED...
Trying to install nrfutil on a system with Python 3.9 but it only installs the old version 5.2.0 which is broken on Python 3. This is the last version before the version check...
I use the internal LFCLOCK to drive my application. Sometimes, I need a more accurate clock to do time measurement. At startup, I can start the external crystal oscillator...
Hi,
I am trying to get Secure UART Bootloader to work and followed the steps mentioned here .
I generated the Keys and updated the dfu_public_key.c file in the project...
Hello,
I'm planning serial wire flash writing from custom board gpio to nRF52840 serial wire.
nRF52840 SWDIO/SWCLK/NRST are connected to a custom board GPIOs.
Is there...
Hi,
We have been working with an end device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b, Softdevice and FreeRTOS.
We built 2 configurations for...
I’m using nRF52810 in my design and for BLE communication I want to use Data Length Extension (DLE). Currently I’m using SDK v 15.2.0 , S112 and since DLE cannot take place...
