I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hi,
We believe we have either a BT communication issue for Nordic Semiconductor ASA NRF52832-QFAB-R
https://www.digikey.com/products/en?keywords=1490-1055-1-ND
...
The comport generated by the USB CDC UART example is showing up as a comport; However when I start sending something my terminal program is crashing.
When I look in the...
I've been trying to run the LWM2M sample from here but I've been running into some issues. Leshan provides two URLs for publicly accessible test LWM2M servers, coap://leshan...
I am using RIGADO Evaluation Board 320-00050
I am using nrfutil v5.2.0 to perform DFU i am able to create DFU package and when sending the package i am facing problems ...
Hi
I combined ble_app_uart with relay example .I am getting a multiple definition error in app_uart_fifo while building.I have added required .c files and their header paths...
The International Conference on Embedded Wireless Systems and Networks will host also this year a dependability competition to benchmark the performance of state-of-the-art...
Hi,
I have some issues flashing or debugging my Thingy91. The problem seems to be related to my specific Thingy91, as I have another Thingy91, which I'm able to flash...
So, I am updating our advertisement data on a regular rate using a timer from freeRTOS on custom piece of software the is for the nRF52840. When only the app code is loaded...
Hi,
I'm trying to deal with long write events (37 bytes long) but on adding a second long write characteristic I'm facing the NRF_ERROR_NO_MEM error on adding it.
The...
Hi Sir,
Since Zigbee_Thread 3.2 released, we prepared two 52840-DKs for consumption test.
One is the door lock example (device #1 Thread_Zigbee_3.2.0\examples\multiprotocol...
I notice that the question has been asked as far back as 3 years without any answer!
There are several parts of the datasheet that mentions internal reference voltage sources...
Good morning Mrs
I have a bluetooth module SKB501 which integrate a NRF52840 chip. In that NRF52840, i want to test a code (ble_app_uart) include in the "nRF5_SDK_15.3.0_59ac345...
Hi. We are using RTC2 in our application to trigger an event at 256Hz. We also have a compare running to trigger a compare event at 32Hz.
I have found that over an hour...
Hello guys,
I am using nRF52840 and SDK 15.3.0. Trying to use SPIM3 device because of the speed.
In my sdk_config.h file, I set both NRFX_SPIM_ENABLED and NRFX_SPIM3_ENABLED...
