I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello!
I am using a nRF52832 with the S132 v4.0.3 softdevice. But I get an error from the softdevice via softdevice_fault_handler.
It gives me id 1(which suggest a NRF_FAULT_ID_SD_ASSERT...
Hi,
I'm using SDK 15.2. The bluetooth disconnects when I enable notifications on nrfConnect. This happens only if I increase the number of bytes to be sent. I'm writing...
hii,
i am currently using light switch example proxy server and proxy clients.
here i am using 3 boards ,2 board(node B &C) are programmed with 4 generic onoff servers...
Hi,
We have a bluetooth product which uses Nrf52840 as the MCU. It composes of a peripheral and a central device of which connect with each other via bluetooth and they...
I have a question about "SEGGER Embedded Studio for ARM V4.12".
I specify a hex file in "Project Options"-> "Debug"-> "Loader"-> "Additional Load File [1]". With this setting...
I have a question about TX Power.
SDK: 15.3.0 Example: ble_app_multirole_lesc Device: EYSHJNZWZ (nRF52832)
The device operates as a “Peripheral”. Is there a way to know...
Hi Devzone!
I merged app_multilink_central and app_uart_c on central side and used app_uart on peripheral side.
I'm using 2 peripherals and 1 central now, and those can...
Are there any examples for disabling/enabling peripherals at runtime for low power purposes on the nRF91 on ncs v1.0.0?
I've seen these threads but they didn't have the...
Hi all We are using nRF9160 gone through all tutorial like GPS,GPIO peripherals,Led blinking Now my main question is How to use PSM mode and eDRX mode program for nRF9160...
I am having trouble getting the nRF9160 DK to find a network running the Asset Tracker than came in the device. It appears to reset after 15 seconds of LED 3 blinking. I can...
I am trying to read from the modem on the nrf9160 DK using the AF_LTE socket and am running to a problem with reading the response from AT+CLAC. I've chosen that command to...
I have been exploring BLE and I am using bt_gatt_discover in my zephyr-based central device (nrf9160) to list the services on a Thingy:52. I am getting the callbacks as expected...
Summary
I'm running into an issue where in certain cases peer manager reports the presence of peers, but when those peers are added to a whitelist I get an NRF_ERROR_NOT_FOUND...
I defined an integer value _ALIGN(4) uint8_t sixteen = 16 and assigned sixteen to a FDS record that is later assigned to the p_data of a custom characteristic. However, when...
