I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
I am working on a project where I need to transfer the data from nRF52832 to ESP8266 through UART. I made the connections RX to TX and TX to RX.
I am using ble_app_uart_c...
Hello everyone,
I am having a problem with powering my nrf51822, I have 2 Li ion batteries to power my nrf51822 and a stepper motor, I put the batteries in series to have...
Hello,
Kindly asking for some guidance... We're working on a solution that requires us to distribute unique data sets (i.e., each nodes gets a different data block, approx...
I am using sdk15 with softdevice 6.0.0 for proximity profile. By keeping bootloader as stable can I change the location of softdevice?? I want to use bootloader at the 0th...
Hi!!
I changed the example of SDK14.0.0's ble_app_uart and I am doing low power consumption.
I used timer interruption and now I am driving with power consumption of 1...
Hi all, I am working on a mesh project. I've read Mesh Technology Overview written by Martin and I wonder what will happen if a node receive two or more messages at the same...
Hello,
I'm developing a BLE application using nRF52 based on SDK15.2 using Sofdevice S132 under Windows.
The nRF52 is used to send data in notification Format. In...
hi....
i am using nrf52832 and peripheral device , microcontroller should run continuously , nrf should be in turn off mode and it should turn on when the data need to send...
Hi all,
We are using nrf52832 board in our product. We used serial dfu method to upload the bootloader. Its done with help of nRFgoStudio application.
We want to know...
Is achieving a data length of 251 possible in SDK 14.0.0, SoftDevicve S132 5.0.0 ? I tried updating my GATT table to 6000 bytes and my NRF_SDH_BLE_GATT_MAX_MTU_SIZE to 251...
Hello all,
I would like to know if anyone is willing to share nRF drivers for ADS1298.
There seems to be a Github repo containing drivers for ADS1298 with arduino.
Has...
hi engineer: I use the software version: SDK15.2; the hardware IC is nRF52832; the protocol stack is s132_nrf52_6.1.0_softdevice; when I add "init.advdata.p_manuf_specific_data...
Hi,
After configure IO and RTC I tried to enter into low power mode however the current consumption doesn't decrease until I call again __SEV (); / __WFE (); / __WFE ();...
I am working on a project where I need to transfer the data from nRF52832 to ESP8266 through UART. I made the connections RX to TX and TX to RX.
I am using ble_app_uart_c...
