Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
I intend to keep a long running clock in the system and use the app_timers(hence RTC1) in a soft device enabled nrf51822 firmware.
I basically have a minute tick and update...
Hi,
I want to run the experimental_ble_app_uart application on our custom nRF51822 board.
However, I could not find a proper bootloader to start the application. Is...
Where can I find an example of using device manager? The SDK doesn't have anything. I am using S110 7.1.0 and SDK 6.1.0 on nrf51822. I am having lots of problems with iOS...
I try to use Android studio to build nRF Beacon project,but it didn't work ,and there are several error .
the error is
Error:(50, 35) No resource found that matches...
Hallo,
I try to use the s310 timeslot API. I open a "session" and then request a timeslot:
check( sd_radio_session_open( nrf_radio_signal_callback ) );
request_radio_slot...
I am trying to implement the pulse counting mentioned in a previous post of the same name, but the code is eluding me. I am using the heart rate service example with new code...
Hello,
I want to implement a firmware update over ble for my application and the SoftDevice 130. Which would be the correct boatloader.hex that I should use? I am working...
Hi,
I am using softdevice-7 and SDK 6.1 for our application.
If I connect using a passkey, first 「BLE_GAP_EVT_SEC_PARAMS_REQUEST」 event occurs, then the 「BLE_GAP_EVT_PASSKEY_DISPLAY...
I have a mature design with several hundred units built using QFAAE0 silicon. Code works. Hardware works. FCC is happy.
I'm considering migration to V3 silicon and maybe...
Hi....
I have PCA10028 DK and i want to make a profile that works both as central and peripheral. As a part of this i tried running S130 demo app found in S130_softdevice...
I need to remember the CCCD's of some service, e.g. service changed. A CCCD is according to spec 2 bytes long. The method to do this is by using sd_ble_gatts_sys_attr_get...
Not sure why but my time is only firing at 250Hz with the prescaler set to 0. Not sure why. Shouldn't it be going at 16Mhz at these settings? (Running on the PCA10028 Board...
Hi,
I am using device as ble-Peripheral SDK nRF51_SDK_7.2.0_cf547b5 and softdevice
version :s110_nrf51822_7.1.0_softdevice.
problem : I am receiving data on Nordic...
