I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
I have tried zephyr/sample/bluetooth/periodic_sync_conn in nrfsdk v2.7 and test on nrf5340 audio dk, and doens't work. the output is:
*** Using Zephyr OS v3.6.99-100befc70c74...
Hi,
How to solve the problem of writing data to flash using the write_data_flash function in save_stack_data function
1.1. I tried to add the function save_stack_data...
Hi! Background (feel free to skip) --------------------------------------- We have 3 nRF52840 boards, connected via ble/NUS as follows:
B also advertises bluetooth HID...
Hi, we are using the nRF9160 in conjunction with the nPM1300. To power off the device, we call lte_lc_power_off() which sends the AT+CFUN=0 command to the modem and waits...
the v2.7.0-5cb85570ca43 zephyr/ndk combination doesn’t work for things using the JSON_TOK_FLOAT type (vs the number type). this is because zephyr/lib/utils/json.c:float_ascii_encode...
I am working on a project in which i have got 100 nodes we are doing it in our custom board. so i need to assign unicast address manaully for each nodes inside it. How can...
When I try to build any application with west I always get a CMake error complaining that it is unable to run the Python version included with the NCS toolchain. The error...
I'm working with a DVK that has an nrF52840 with a Sierra Wireless HL7800 modem. The modem is connected physically to UART1 while the UART0 is used for the following as shown...
Hello
I am at the early stage of evaluation of a nRF52840 USB Dongle and I have installed all software on my Win 11 PC.
Just trying to check that everything is working...
We have made 2 partition of Internal flash. One is for running Application and Other for storing some configuration. I am trying to erase the page of 2nd partition, and it...
Hi,
I have been performing a fresh install of the toolchain following the nordic's "nRF Connect for VS Code" page, as well as the YouTube video "Introducing nRF Connect...
Hello,
Developing a custom board with nRF9160 as application CPU and nRF52810 as BLE Controller. Connected via SPI + reset + irq lines to the 52810. The design is a copy...
This might be a simple one to answer but I'm struggling to find documentation on what to do here since we're still using an ancient SDK on 9160.
I have a working board file...
Hello,
We have a BLE connection issue. We want to connect a Windows 11 laptop with a nrf5340 eval board.
The connection procedure can fail by a disconnection with reason...
I have a custom PCBA with which has the flow of:
- Boot
- Advertise some temperature data read from TWI with a 5 second timeout using `ble_adv_fast_timeout`.
- I then...
