I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
Hello, Im trying to use the Unity framework. I was able to run a simple test, however I would like to change the print function - UNITY_OUTPUT_CHAR . From the nrf/test/unity...
Hi
Is there a way to do this quicker?
I have my own custom characteristics. Is it like bonding will imrpove this? Atleast for the case of a reconnection?
Is it bonding...
Hello,
I am running a simple experiment to turn on all GPIO pins to active on the NRF52840.
The code attached works on the NRF52840-DK, and I am able to measure 3v on...
Just started another project using an nrf52840 dev board, and the printk() call produces no output. There is no output for Zephy booting, or anything else. I have tried both...
Hi,
according to my system architect it should be possible to use a standard https://github.com/NordicSemiconductor/pc-ble-driver on the nRF52840 Dongle for implementing...
Hi guys, I'm trying to measure deep-sleep current of my application quite precisely to obtain a reference measurement to evaluate against for further improvements. The setup...
I tried to add a chip of our own design to NCS, but when I tried to write the device description file, I ran into two problems:
1.Even if the chip description file is compiled...
Hi,
I'm using the example project usbd_msc and I am having no luck having the volume come up on windows when I plug in the nRF_USB line. I can see "nRF52 USB MSC Demo...
We are currently getting our firmware ready to test devices for FCC and other radio testing. We have an AThost-like setup that passes AT commands from a terminal over a BLE...
.Hi Nordic Support team,
I'm using NRF52832, SoftDevice S132, SDK version is nRF5_SDK_17.1.0_ddde560.
I want to transmit 9 bytes of data collected from an I2C sensor...
Hi,
the I2C burst write function below work perfectly <16 number of bytes. Once I transfer more that this, the return code throws an error "-28" and my scope doesnt even...
Hello, I would like to develop an automated tool for our production line to use to perform DFU on our nRF52832 system. Is it possible to communicate with the nRF52 Dev kit...
Hi, I developed a custom board and I am able to toggle other IO pins but somehow pin 10, 9 wasn't working. After some research, I found that NFC must be disabled to make it...
Hi,
I am trying to set EDRx en LOG_INF the result using following code:
static struct lte_lc_edrx_cfg drx_cfg ;
//enable EDRx
LOG_INF("== Setting EDRx =...
Hi,
I have a custom board with a nRF52840 and the nRF21540 FEM. To control my FEM, I have added the following to my code to my nRF52840_nRF52840.dts file:
/ {
nrf_radio_fem...
