Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
I have 2 nrf5340 devices, one running the Unicast Client and one running the Unicast Server. On the initial connection I am able to successfully stream audio.
On a restart...
I have been using the nRF7002 DK board; the nRF7002 uses the QSPI bus and the external NOR flash uses SPI.
The nRF WiFi driver's HAL and interface functions all require...
Hi,
I made DFU procedure with a distributor (nRF52840 DK) and one target (nRF52840 dongle): procedure completed successfully in approximately 45min
Then I made:DFU procedure...
The nRF5340DK's are not programmable on my pc. I have no issues using nRF52DK and nRF52840DK. I have 3 different nRF5340DK's, they all have the same issue.
When I try nrfjprog...
Hi There,
We're new to Nordic and in the process of attempting to move our custom Xamarin application and boards over to use the nRF52832 and the nRF Connect SDK. Has anyone...
Hello,
I used two samples, application_update and SLM, to test and try updating the app from application_update to SLM. I first downloaded the firmware of application_update...
I would like to store context information for each connection, but with central and peripheral connections storing different information. Ideally, this is done in two separate...
hi support team,
we can see the slide in this link： /cfs-file/__key/communityserver-discussions-components-files/4/3201.Measuring_5F00_distance_5F00_with_5F00_Nordic_5F00_Distance_5F00_Toolbox_5F00_slides...
hello Nordic
we are working with nrf52832 and nrf52840 running with ncs v2.5.0 (waiting for v2.7.0 cause 2.6.0 have some issues with cmsis fft tables that prevent us from...
Hi
We are using STM32 board as a HOST controller and NRF9160 as cellular modem. On the STM32 board PPP client is running over serial interface.
We need PPP server support...
Hi,
I own an nRF5340 Audio DK, on which I successfully run the example audio application (in BIS mode).
I also have my own customized board, based on Raytac MDBT53v, for...
I have a nRF9160 custom board. I am using 2 UARTs (UART0 and UART2). I need to have an RX interrupt on both UARTs. I have identical setups and configuration and code. The...
We are using PC-BLE-DRIVER-JS for our central and zephyr in our peripheral (833). The central bonded with the peripheral only when the id (IRK) param in our central is set...
Hi all!
Hopefully this doesn't come off as too much of an ignorant question, but I'm having a hard time understanding the pinout of the Thingy 91 since I can't map where...
I´m trying to design a compact circuit for the NRF91, since i have limited space i´m planning to do a board stackup with the antenna board on top. Right now my board is 50mm...
