Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hi everyone, and thanks for all the help provided on this site !
I have tried to flash a MDBT42Q using the nrf82832-DK (PCA10040) and it works fine for simple peripheral...
Hello,
Aim : Our application uses the PC-BLE driver for serialization purpose as well as the nrfutil for DFU purpose in the same script, we switch between the two by opening...
Hi,
I am developing a BLE sensor based on nRF52840 SoC (QIAA aQFN 73). I would like to get some clarrification regarding following points while hardware design. Thanks for...
Hi there,
We intend on using the default Serial LTE Modem example on the nrf9160 in our product. We will then communicate to the modem with AT commands from an external...
I'm trying to program a nrf52832 chip with a nrf52dk board by configuration below, referred to https://devzone.nordicsemi.com/f/nordic-q-a/14058/external-programming-using...
Hello,
Since the last update some of the includes in my files are being marked by VSCode as "cannot open source file xxx (1696)"
The application compiles fine...
Hi! The nRF9160 has a nice, accurate LFXO integrated. I'm assuming that it's also active most of the time anyway to provide timing for the modem (assuming one is using the...
Hi, I have the following questions. Please help me answer them: Using the protocol stack of the above version, one master and two slaves are disconnected when reconnecting...
Hello,
In my project i am using nrf52840 with my custom board and to upload the code through NRF_CONNECT application with soft device its uploading properly but with segger...
I'm interested to know if can I have the Zigbee protocol on the nRF5340 microcontroller and use a web browser (from my phone for example) and get a http page from the MCU...
Hi,
I've connected in BLE two devices
- NRF52840 DK as "central", connected to PC via nRF Connect For Desktop v3.11.0 -> Bluetooth Low Energy v3.0.1 - NRF5340 based custom...
Hello Sir/mam,
I am working on BMS I want to prefer nrf9160 dk board for my project . I want know is there any way or document available for communicate with Modbus or can...
Hi there, I have compiled the hello world example of Zephyr and flashed my NRF 5340 DK successfully. Now when I want to use the COM port to see the results on my ubuntu I...
I have issues running the upgrade of nRF Conenct (too old linux version to run nRF Connect 3).
I tried to downgrade, downloaded v2.6.2 appimage from https://github.com/NordicSemiconductor...
I am using nRF Connect Toolchain v 1.9.1 on a nrf52832 processor and I am not able to access any of the GATT characteristics beyond the 6th characteristic that I define. The...
