I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I have to initialize a i2c multiplexer, for that I am sending the device address and register address to be written using the function:
nrf_drv_twi_tx(&m_twi, (0x70), tx_buf...
Hi,
I'm currently using nRF Connect SDK v1.9.0 and developing on a nRF52832 onto a custom board. I'm using a BMI090L from Bosch connected over i2c.
I'm trying to suspend...
Hi.
Encountering an intermittent issue where, after a DFU (either OTA using Nordic Device Manager or over usb serial using dfu-util on Linux), the image is reportedly in...
In the DTS file for I2C, how do you set the port of the pin specified?
&i2c0 { compatible = "nordic,nrf-twi"; status = "okay"; sda-pin = <26>; scl-pin = <27>; };
In...
Hi,
I have a question about the whitelist，when we use the function "pm_whitelist_set()" to set the whitelist，whether the whitelist is stored in RAM or FLASH? I traced the...
Hello,
I am using nrf52810 with custom board and i have created DFU for uploading a OTA file previously its working fine but i don't know what happens now BLE is getting...
Hi:
When i read data from the device nrf52833 to android app, only get 600byte data and it should be 4096byte. The app use the Android-BLE-Library-2.4.0 lib.
The nrf52833...
Hi,
I have a question on SDK release plans. There is a change awaiting for release (merged after 1.9.1) and it would be nice to develop them with an official release, including...
Hello!
We are two students working on IO-Link Wireless as a bachelor thesis project. Our task is to make a Wireless Master prototype using the nrf52840 DK kit from nordic...
I am making a ble beacon application. I need to send more than 30 bytes of data via advertisement. How can I do? Because UUID data will not be enough for me.
Hello everyone and hello kindly nRF support team!!
One question again sry. I am using SDK 1.9.1 through VS Code and working on the nRF Connect SDK Tutorial - Part 2 -...
Here is the main.c file for AES CTR - /examples/crypto/nrf_crypto/aes/aes_ctr example project
'NORDIC SEMICONDUCTORAES&MAC TEST' is the key
Encrypted hex output: "12 DD...
Hi
I have been struggling with increased power consumption after SPI slave usage, and finally seems to have found a solution, based on errata 89.
However looking through...
Dear all,
With nrf9160, I start GPS function.
at#xgps = 1,1
If GPS positioning is successful, I will receive #XGPSP and $GPGGA information. Though I haven't specified...
